New forum group, Nor-Cal Mopars

-
Anyone doing any racing at Sonoma this year?
Only problem is that you cannot just go to watch. Each driver is allowed additional one person but everyone is supposed to stay in the car, social distance, blah blah. Even though my "new" car isn't quite finished, I cannot imagine sitting there cooking away in the afternoon sun (with no AC)!
 
Only problem is that you cannot just go to watch. Each driver is allowed additional one person but everyone is supposed to stay in the car, social distance, blah blah. Even though my "new" car isn't quite finished, I cannot imagine sitting there cooking away in the afternoon sun (with no AC)!
You don’t have to stay in the car. All you have to do is wear a mask the whole time. You have to enter a car in order to be there or be a crew member. You can have one crew member with you if you entered a car. I’ve gone twice this year and it’s been pretty good
 
This thread has been quite so just making some noise.:thumbsup:

I have been working on changing the speedometer cable on my car which is drama cause of sourcing the correct one. Still working on it as of now... need to pull the upper of the two piece cable from the speedo gage. Then i'll see where i stand.

Also, changing my neutral safety switch since I saw that it some how got disconnected and started melting against the exhaust. I also noticed that wire connecting to the starter relay ran not only from the trans/NSS but also to bulk head terminal where the reverse lights should be connected. :BangHead: turning into a bigger project than i was expecting.

What's everyone else been up too?
 
Engine and tranny out of my ‘70 Swinger. I’ve been prepping the engine bay for paint. Engine is done but still have to reassemble the tranny too.

I’m replacing the pigtail to my NSS as well. I had a tranny leak and the rubber boot around the terminals is pretty much crap. New switch too. Sometimes I’d have to shift in and out of park a couple times to start the engine.

These projects always snowball don’t they? Figure while I’m in the neighborhood I’d replace the fifty year old positive battery cable. The insulation down near the starter was pretty stiff and cracking. It wasn’t contacting any grounds but why take a chance. Bought a reproduction from Classic Industries. Looks exact. Hopefully the lasting quality is as good as it looks.

Good luck on that speedo cable. Uff dah! They’re not impossible but there’s a ton of things I’d much rather do than that.
 
This thread has been quite so just making some noise.:thumbsup:

I have been working on changing the speedometer cable on my car which is drama cause of sourcing the correct one. Still working on it as of now... need to pull the upper of the two piece cable from the speedo gage. Then i'll see where i stand.

Also, changing my neutral safety switch since I saw that it some how got disconnected and started melting against the exhaust. I also noticed that wire connecting to the starter relay ran not only from the trans/NSS but also to bulk head terminal where the reverse lights should be connected. :BangHead: turning into a bigger project than i was expecting.

What's everyone else been up too?
This weekend I hope to have time to finish brake plumbing and carpet install on my 65 Bcuda.
 
Our big local show has been cancelled for the second year. Coincidence that the only time I’ve missed was last year with a broken motor. I was thinking I’d have her running for it this year but now the pressure is off a little.
 
Been working on the Barracuda convertible. Need to take it to my buddy's shop to get the trunk drops and quarter patches installed. Maybe next week. It runs like crap right now which I suspect to be sticking valves. Heads will come back off after the body work as I am also working another, even bigger project. A second two-car garage attached to the side of my house which will also include RV parking (no RV yet, but need to have room for it). The first pic came down. The new garage will be 19'9" x 20' (maybe 21') with an additional 14' x 5' or 6' addition on the right side. Lots of work still to do, but the tear down is complete. Now to do some cleanup and get some plans drawn up. The carport on the right side of the original garage will also be coming down after the new garage is built. Pulled some money out of the house with a refi and the payment only went up $28...Also gonna do dual pane windows (already ordered), stucco work, and kitchen remodel...
DSC01442.JPG
20210209_145452.jpg
House.jpg
 
Picked up this rust bucket on Friday for a steal. Gonna just bomb it around as is. Didn't run worth a crud because the company who rebuilt the carb never cleaned out the idle well in the Holley 1920 and the idle emulsion tube was clogged. Runs like a clock after 10 minutes of work.
Pgcio0oh.jpg

LDV2sgqh.jpg

CXihPgzh.jpg
 
I’ll attend a few to look up friends and spectate for sure. I’m not sure if my Dart will be completed by then. I’ll finish cleaning up and priming the engine bay this weekend. Plan to paint it next weekend. The engine is done. The tranny is still in pieces on the bench and in totes. I have everything I need with the exception of time. I’m hoping to have her done but not counting on it.

Will you be up here at all?
 
I’m looking to head up for the one on the 17th. Thought there was one in Anderson a little earlier in the day but I don’t see that one on the list anymore. Will be a long day and great reliability run for the Jalopy.
 
Good For You!
I saw this one on Craigslist.
Thanks! I was talking with the owner since November. No one wanted it because of the rust and he didn't like my offers. I kept at it and traded an old scooter for it.

Looking forward to seeing that one cruising around! :thumbsup:

Oh yeah, I definately will be cruising it around. I think I'll keep it very much like it is. Will have a wet trunk during winter tho. Haha.
 
That seems like a worthy project. We have been ‘fantasy shopping’ on the internet for houses with a 2-car garage (my priority, not my wife's)...

Been working on the Barracuda convertible. Need to take it to my buddy's shop to get the trunk drops and quarter patches installed. Maybe next week. It runs like crap right now which I suspect to be sticking valves. Heads will come back off after the body work as I am also working another, even bigger project. A second two-car garage attached to the side of my house which will also include RV parking (no RV yet, but need to have room for it). The first pic came down. The new garage will be 19'9" x 20' (maybe 21') with an additional 14' x 5' or 6' addition on the right side. Lots of work still to do, but the tear down is complete. Now to do some cleanup and get some plans drawn up. The carport on the right side of the original garage will also be coming down after the new garage is built. Pulled some money out of the house with a refi and the payment only went up $28...Also gonna do dual pane windows (already ordered), stucco work, and kitchen remodel...View attachment 1715688635 View attachment 1715688637 View attachment 1715688638
 
That seems like a worthy project. We have been ‘fantasy shopping’ on the internet for houses with a 2-car garage (my priority, not my wife's)...

Good luck with that where you are. Not sure what your budget is, though...
 
I've noticed more folks joining from around the northern parts of California, so I took just a quick moment to throw together a new forum group, Nor-Cal Mopars. The group is open to anyone and hopefully folks from the area can join & use it to connect with other Mopar folks & talk issues, shows, cruises, shop recommendations & who knows what. The group can be whatever folks make it. Stop by & join the group.

http://www.forabodiesonly.com/mopar/group.php?groupid=28

~Sae
Update ? I am from sacramento.
 
Good luck with that where you are. Not sure what your budget is, though...

Haha, we weren't looking in MY neighborhood... have to knock off a few Brinks trucks for that. We were actually contemplating moving to Oregon at some undetermined future date. We both have family up there.
 
Haha, we weren't looking in MY neighborhood... have to knock off a few Brinks trucks for that. We were actually contemplating moving to Oregon at some undetermined future date. We both have family up there.

I have long ago given up figuring out what other people's budgets are. I know some very wealthy people (most aren't into cars, though). Oregon is too much rain for me. I've looked around and just haven't seen anywhere else I want to live even though I hate the politics of this state.

The architect came by this morning. I think that bill is gong to be more expensive than the framing...Now to get the old concrete up...
 
Haha, we weren't looking in MY neighborhood... have to knock off a few Brinks trucks for that. We were actually contemplating moving to Oregon at some undetermined future date. We both have family up there.
Tinyhouse Nation is in Oregon
 
hey anyone got any good leads on a body shop in the bay area? I want to get some rust bubbles and surface rust taken care of
 
New old guy here that's been wrenching since early 60's. Mostly Chevies and a couple of 50's Ford and one '52 Dodge that I commuted to work in the 70's.
Decided to buy this '63 Valiant Convertible. It's a turn-key and drove it home about 125 miles. Will inspect it more later this or next week. Sorry this is the only pics I have. Will take more later.

IMG_4916.jpg


IMG_4917.jpg


Valiant1.JPG


Valiant4.JPG


Valiant5.JPG


Valiant6.JPG
 
-
Back
Top