FS/FT: The "Green Meanie" - 1971 Plymouth duster race car
Steve Senkevich
Beaver Falls, PA 15010
[email protected]
(724) 630-8327 - Drop me a TEXT, It's the best way to get in contact with me. I am more than willing to answer any of your questions!
$5,000 FIRM
So the story is for the past few years my brother and I have been sitting on this car but have lost interest in working on it. I has been doing nothing but collecting dust, and we have decided to build the 426 Hemi in our basement for our new project:eveilgrin so this little guy has to go.
The car is being sold as a rolling chasis with no motor/trans. However I do have all parts necessary to complete this car, and will go with it. (seals, glass, grill, lights, panels, door handles/locks, etc.) I have every single part to complete the Duster! The car has a CLEAN title.
Here's what was done:
* Full wheel tub
* 12 Pint Roll Cage
* One Peice Fiberglass Front End
* Fiberglass Deck Lid
* Reinforced 8 3/4 Axle Housing
* 35 Spline Axels
* 4-Link Suspension with Coil-overs
* Fuel Cell
* Manual Steering
* M/T DOT slicks - 33 x 19.5 15 LT
* M/T Front Tire (can't remember the size I'll look tomorrow)
I have a built 340 (under 3k on the motor) that I'm willing to go with this car for $1,200. This motor made 452whp/431wtq in my red '74 Duster. Royal Purple is the only Oil I use in my motors
Specs:
* 0.030 overbore
* TRW Pistons (11:1 compression ratio)
* Clevite Bearings
* MOPAR Purple Camshaft
* J heads (Six pack heads)
* Edlebrock Intake Manifold
* Holly 750 Dual-Pumper
* MOPAR Performance Valve Covers
* MOPAR Performance Air Cleaner assembly
I know I don't have too many posts on this forums but check me out on srtforums.com (senk04srt). I am a straight-forward, No Bullshit seller.
Steve Senkevich
Beaver Falls, PA 15010
[email protected]
(724) 630-8327 - Drop me a TEXT, It's the best way to get in contact with me. I am more than willing to answer any of your questions!
$5,000 FIRM
So the story is for the past few years my brother and I have been sitting on this car but have lost interest in working on it. I has been doing nothing but collecting dust, and we have decided to build the 426 Hemi in our basement for our new project:eveilgrin so this little guy has to go.
The car is being sold as a rolling chasis with no motor/trans. However I do have all parts necessary to complete this car, and will go with it. (seals, glass, grill, lights, panels, door handles/locks, etc.) I have every single part to complete the Duster! The car has a CLEAN title.
Here's what was done:
* Full wheel tub
* 12 Pint Roll Cage
* One Peice Fiberglass Front End
* Fiberglass Deck Lid
* Reinforced 8 3/4 Axle Housing
* 35 Spline Axels
* 4-Link Suspension with Coil-overs
* Fuel Cell
* Manual Steering
* M/T DOT slicks - 33 x 19.5 15 LT
* M/T Front Tire (can't remember the size I'll look tomorrow)
I have a built 340 (under 3k on the motor) that I'm willing to go with this car for $1,200. This motor made 452whp/431wtq in my red '74 Duster. Royal Purple is the only Oil I use in my motors
Specs:
* 0.030 overbore
* TRW Pistons (11:1 compression ratio)
* Clevite Bearings
* MOPAR Purple Camshaft
* J heads (Six pack heads)
* Edlebrock Intake Manifold
* Holly 750 Dual-Pumper
* MOPAR Performance Valve Covers
* MOPAR Performance Air Cleaner assembly
I know I don't have too many posts on this forums but check me out on srtforums.com (senk04srt). I am a straight-forward, No Bullshit seller.
