Separate names with a comma.
Although not the cause of the poor brake performance, your parking brake cable connection under the dash is installed incorrectly as pointed out...
Good work!!! Similar to my experience with Edelbrock heads and the B3 kit. It took a few tries to get the clearance. I didn't have to remove...
I second that... Great job! I also think the angle iron should be more than adequate. There is usually a decent radius on the inside of the...
On my first trunk mounted battery project I switched the negative. Not a race car and seemed the easiest. On my new project (also not a race...
My suggestion is to search the internet for 'MRBF Terminal Fuse Block'. They have various ratings up to 300 Amps. They are compact. It's a fuse...
I was in a similar situation, just renewed for 3 years and figured my money was gone. I called them, talked to a polite person and they refunded...
I've heard the reference to a "peanut" compressor as well and came to the conclusion it applies to the Sanden SD-7B10. It's the shortest...
I got my BAM lifters from Brian at IMM Engines located in Indio, California. He is a Mopar guy.Also as Rumblefish mentioned, Hughes sells them...
I took my own advice on my suggestion to YR. I'm working on my own stroker 340 and was doing some test fitting of parts and such. I went ahead...
Hi YR, You might try spinning the oil pump when you have the timing cover off. If there are no plugs behind the cam plate I bet you will see oil...
I'll stay out of the fight with regards to which opinion is right or wrong, but I'll share my personal experience on the cam plate and gallery...
For what it's worth, I located a manual/wiring diagram for a '91 Ranger and the inertia switch is wired in series with the fuel pump. It's...
I am also planning to use the Ranger inertia switch as well on a similar electric pump setup. My current idea is to put it in the kick panel...
Hi Dart19666,Can you elaborate more on this? I'm thinking that if the portion of the lifter where the link bar attaches is on the piston side...
Suction is just a way to describe "low pressure".At sea level atmospheric pressure us about 14.7 PSI. It's less at higher elevations. That's...
Thanks for that feedback. I was thinking I might go to the parts store and see if they would let me measure one. The pump I'm working...
I picked up a used Edelbrock water pump from a Mopar swap meet a while back. I'm finally getting around to installing it on my 340 stroker...
Great job! Excellent work!I finished up fab work on a 67 Dart for a TKO-600 a few months ago. Looking at this makes the T56 Magnum more...
Add me to the list of people that used the Harley wrinkle finish. It was many years ago and turned out good. Slightly uneven result, but that...
It might turn out that it is a small sector shaft. Again, from the website, it wasn't obvious which it was. Good luck!
The sector shaft connects to the pitman arm. There are two sizes which are grouped into "large" and "small". Most factory manual boxes are small...
Thanks for the links! The best I can determine it looks like the 82-70002NQ is a new, quick ratio, and possibly large sector. The BuyAutoParts...
Are you talking about the Lares version for $225 Can you share your source? I'm interested in purchasing another.
The Flaming River box, at least the one I looked at, FR1540, is cast iron. The Lares Corp version is aluminum and appears to be an exact or...
With regards to your first link, you can find a less expensive fast ratio version at Rockauto from Lares Corp. They offer a new one and a...
I was planning to add A/C to my 67 Dart project that was originally a non-A/C car. The car is a small block manual trans car. I figured on...
Sorry, bracket is not for sale. It's my only one. I'm not sure what it is actually called. I looked at the service manual (67) and I didn't...
You are missing the bracket that looks like the following.[ATTACH]
Great information that I was not aware of. Thank You!
Thanks everyone for the posts! I've got a purchase from a member in the works.
