Separate names with a comma.
@67Dart273 If you don't mind, could you go through what it took to run a 273 crank in a 340? I've got a 340 block without a crank and I also...
I wouldn't hesitate to use a good quality rubber line between the dryer and the rest of the rigid run or over to the compressor. I need to get a...
It's like wet sand blasting with a really fine media. Supposed to be very gentle on the parts. Popular for carb rebuilds and other aluminum,...
If you’ve ever skinned a mature buck you would understand the trouble the guy in the story had. The hide on their necks is extremely thick and the...
Where are you located? There is a set of Hughes P/N 5321 lifters on Craigslist in Chicago. Maybe he'll ship them. They've been listed for a few...
That looks like casting flash in the corner of the water port, not a crack. Shouldn’t affect anything. Scratches are no bueno though.
Straight cut gears of good quality, properly setup will run pretty quiet. Not silent, but not screaming either and pretty close to a chain drive....
That's what magazine articles are about, at the end of it. They don't make much money off the hard copy or subscription. It's the advertisers...
I think another big reason hydraulic are preferred is they are seen as no maintenance. Once setup, you shouldn't have to go back and adjust them....
Maybe that's why many of the race blocks are setup for roller bearings and sometimes larger cores?
How “big” of a cam could this motor support and still be a reasonable street driven car? I love that torque curve and would think a single plane...
Are you sure about the In/Ex ratios you stated? I don't remember ever seeing the exhaust being that much higher ratio than the intake. I guess...
I hope that is a typo on the specs. 5cfm would barely run my cutoff grinder.
If you are handy, look up DIY Rotary Phase Converter. You generate three phase power off your single phase by running a three phase motor and...
For someone doing it for business or whose spare time is critically limited, I would agree with you. But in my case I love jobs like this. It’s...
Those look nice. Pretty much what I plan to do. $400 isn't a bad price for something that is essentially a one off. If you wanted to sell a...
Member Rocket had a couple sets for very reasonable price. I hemmed and hawed too long and they are gone now and I'm not sure there will be any...
I have the "opportunity" to upgrade the main caps on a 340 block I was hoping to build, pending sonic checks. Opportunity comes from the main...
Online, try McMaster-Carr or Bolt Depot next time. I won't use Fastenal after the local store refused to sell me anything unless I had a $25...
Get them with Torx type heads if you can find them. A lot less likely to strip out than hex. I can't tell you how many I had to use a punch,...
Unless there is something special I can’t see in the pic those are just standard flat head socket cap screws. Should be able to get them from any...
Anyone have a pair of these kicks? Vintage Cuda with Cactus Custom Casual High Top lace up Canvas shoes sneakers Drop shipping|Running Shoes| -...
I'm really curious about your flow bench. Specifically the instrumentation. Having something like that to play with on these long days of near...
I understand this part about the nut sitting down in the depression, but I don't see how these stiff grinding disks are going to flex down into...
I picked up a nice pneumatic grinder at a swap meet a couple months ago. Runs well with a lot of torque and has a 7/8" bushing on the nut. Came...
TP??
Scat kit. Go with the 4” crank IMO. That rag really was in the motor? Maybe part of it got pulled in and jammed up the worx
Sharp looking little thing. Kid should like it.
They rust worse that the normally horrible Mopar rust, in my experience. Everything is available but still a PITA and not free.
The Campbell Hausfeld is $33 there now. A little cheaper from Amazon. but it looks pretty decent and would be in budget. The Scat Blast looks...
