Separate names with a comma.
After a little tinkering i found a vaccum leak which promoted a lean condition, hence all that initial timing. A great read of that article by the...
So then what about a 5.2 magnum carbed? Ive got a stock 5.2 i put an airgap intake on and a 1405 600 edelbrock carb. I set initial at 15 and it...
Summit racing has high zinc oil called classic car oil. I use that stuff always. But cant say i have 20,000 miles on an engine with it. So i...
Yes! I also love the Thrush Turbo, flows well and quiet at idle and cruise with full exhaust but sounds great when the throttle is down. No...
I havent been on here in so long! To answer the original question with my personal experience. I put a 5.2 in my 73 dodge D100 with an Edelbrock...
So I am on a stupid tight schedule, like a couple days. Long story short, has anyone reused rod bolts on a stock 360? In a perfect world I know to...
Maybe I'm wrong... I must be thinking of something else. Sorry!
No those are not needed per say. I've heard of people milling them out for more plenum volume. I've never used one on any engine of mine so I...
I love watching how wrong the three of you are. Go back and actually read what was said. Yes there have been some helpful comments. And also if...
Yes please. Delete this thread so these unhelpful.comments can be ridden of and I can start another that's actually helpful. And yes. I did state...
The first one felt like the bearing race was pitted. After I spun it by hand, I replaced it with this new one and it makes the same sound but I...
Like I said, positive and contributing replies please. Thanks for understanding and not replying. I appreciate it.
Buying a more expensive bearing doesn't prove or disprove this one is bad from the get go. A less expensive bearing may or may not fail sooner...
Please take your antagonistic, underlying sarcasm somewhere else. You deem yourself cunning, however your playing a child's game. On a thread...
So no possibility of the bearings being bad off the shelf. Alright, well for the future readers I'm going to prove it right or wrong. Since I...
Thank you for pointing out the alignment possibility. Although I don't understand why a little toe in would make bearings go on the Fritz. Don't...
I don't think you read the post or any other part of the post. I've said hub assembly a few times already. I know how to assemble a tapered...
No, nothing arry at all. I know the tires make sound going down the road, but this sound is definitely a wheel bearing type sound. I don't see how...
It's a hub assembly for a 07 dodge magnum. I started to suspect something else, but what else makes a whirring sound like a bad wheel bearing and...
So, long story short. I get the whirring sound of a bad wheel bearing and I know it's in the front end. So I buy both if them because it sounds...
Like Rusty says. Milling for power isn't very cost efficient. Especially since you have closed chambered heads. Port them nicely and appreciate...
Like others have said. Ditch the flex fan and get a viscous clutch fan and a shroud. You shouldn't run without a thermostat as it could cause...
Not useful? Get out. Lol. You seem to know better than I. I have no idea how many output shaft spline sizes they made.
See there ya go lol. Thank you AJ haha.
Either scrounge one up online or a swap meet or possibly get a new one. I think brewers performance would sell them. It's definitely an A230. I...
Beats me. I'm assuming it's one of those things where they hAve no idea what they are talking about. I knew I was right.
A230 3 speed. Full synchro. Snap a picture of the front horizontally. Pretty sure it's an A230. I use one in my 360 duster. Very tough.
I knew it! Ha ha! I was gonna say 2007. What were the options in 1970 anyway? RT and T/A? Are there only two aside from the base model.
Having a bet with some non Mopar guys, when did the SRT nameplate come out? I am being told the SRT came out on a challenger in 1970. I'm pretty...
