Separate names with a comma.
Jim, Geoff B. here from Killara. If you screw the mixture screws all the way in, does it stall the engine? It should. If it doesn't, it sounds...
As suggested by others, I would disconnect the VA. The way it works in Chrys dizzies, with it's over-centering action, might cause reluctor to...
YR, I answered your questions, you just didn't like the answers.To clarify the weight of air: A cube with sides 100 ft long weighs 38 tons.
I just had a look at the Summit site, more than one available for $174. Summit part #: URM-6-6162.Also, I forgot there was a core charge, I...
I think the company's name is Uremco. It was $174. I thought that was pretty cheap for a carb that looks new, & has been out of production for...
Just wanted to post some feedback. Carb I ordered was a #6324, 850 CFM originally off a 73 440. The 6324 is what I got. Overall finish was nice &...
RRR, Yep remember the dist gaskets, prior to the o ring. Still have a bunch hanging from the rafters....Makes no difference. You do NOT need a...
YR. My answers & suggestions are predicated on what the OP said in his initial post. I will repeat it again: 90% street driving. If it was 50/50...
Jim, In one of his books he says he trained as an aero space engineer. if you want to read a really interesting book, his book on head porting...
Yep, tighten the spring if you want to slow AV action.
Yes, I 'pick' at things that are incorrect. Oh, & I understand the concept...& far better than you do. Of course long coil + & - wires will...
YR, There have been PLENTY of tests where DP intakes have made more power than SP intakes throughout the rpm range for street drivers. [...
Either of the two blue seals above is what you want.
Need more info on cam type, max rpm etc. There is more than likely is a BH spring to do the job, as the range keeps expanding. Also look at...
Dart, You seem to take many things out of context. Where to start. Have no idea which 5-6' wire you are talking about that has' inductance'. With...
Three key words in the original post: 90% street driven. The comment that a single plane intake has better fuel distribution is incorrect, because...
Sigh. The number on the stat is is it's opening temp, NOT the fully open temp [ post #30 ]. The stat will require another 20-30* above it's...
Don't know if you guys know this about David Vizard....but a lot of his early racing success was with.....Chryslers! Specifically the Chrys 4 cyl...
I have a new Rolon chain for a Pontiac, free.... One side of the links says Rolon. Other side says India.....
You do not need a separate grd wire, as the module grounds to the dist body. The dist clamp is the ground source. Roughen the tabs/feet on the...
Pishta, Not all dampeners are interference fit, like Mopar. Some like Pontiac just slide on. They are kept tight by a very tight crank bolt,...
Two comments.[1] I know from experience that blocks that sit unused for years develop rust in the water jackets, sometimes like grains of rice....
A most important fact has not been mentioned, unless I missed it. The coil current grounds through the ECU box. So make sure the mounting...
Use a Chebby engine? Sorry, couldn't resist.....
No, not counterfeits. The fretting occurred at the wrap around under the trunnion brg & also the roller tip axle.
Wrong way to build an engine. Decide on limits, parameters [ eg, how rough an idle you can tolerate ] & THEN select the parts to do the job.
That is a lot of adv duration for 232 @ 050. Consider the Comp cams 280 H magnum cam: it has 230 @ 050, but adv duration [ @ 0.006" tappet lift ]...
To make 400hp, you need intake flow of roughly 200 cfm or slightly more. Might be doable with smaller valves, but in my opinion 2.02" valves would...
The 346 shows more int duration than exh, the only cam in the chart that has that. Is it a typo?
Car has done less than 1500m. Has it run hot the whole time, or is this something new?
