Separate names with a comma.
But would this void the warranty, if something like a leaky weld or tube was discovered after being put into use? Thanks
I tried that Driven assembly grease and they made a believer outta me....Good stuff.
It's been said already but transfer slot/throttle blade position is very important. The fact that it doesn't die when turning the screws all the...
If the TF240s valves don't interfere until--whatever IQ found, like .7xx lift--I wouldn't worry about the Stealths. That does NOT mean I wouldn't...
Yeah the "hardware issue" is a BS excuse and has been from the beginning. They haven't had the bare castings available either, not for awhile. I'm...
And being a band known for their big beards, the drummer DIDN'T have one most of the time even though his name is Frank Beard!:D
Here, these are .035 longer than stock and they're ready to ship.. Manley 25803-16 Manley Chromoly Swedged End Pushrods | Summit RacingThat's...
Well said....kaboom starts on the top (chamber) side of the gasket.And I have to quote you again,....because 99% of all the internet 'fail...
I enjoy the back-to-back testing they do, but I mostly watch Roadkill Garage for a couple reasons....Lots of Mopar fun and they aren't afraid to...
20-25 lb/in difference on the seat2s. The springs specs say 420 lb/in rate but they checked at just over 430. Tested seat pressures ranged from...
Well one of the best Mopar head porters around has been known to drop in from time to time... He's even got 'Porter' for a last name!:D @PRH
And just a word of caution...I know everyone says they'll get their heads checked, and I know TF are some of the nicest OOTB quality-wise...but...
Forget it Rumble, it appears this thread is more about people's own conspiracy fantasies rather than facts...If you look at the timing and what...
The thing about valve/hardware availability being the issue was BS....the bare castings weren't in stock either. 440 source had some 240s in...
Last two BB Milodon pans I used had weeps right out of the side of the pan where the sump baffles were welded. Milodon has said the pan rails are...
What did IQ52 always say? "You gotta be smarter than your _______"[ATTACH]Best thing you can do is test it before installing the engine,...
He's a shadowy figure for sure!:D
I know you're talking WP housing bolts, but since you're there--the top left timing cover bolt goes through into the valley on some (all?)...
Cool man! Glad you're all set. Mike's a good dude.
Okay...the discussion was on shaft mounted rockers so I chimed in. They can both have issues as far as geometry is concerned. Be cool to see some...
A member over on B-bods used the recommended 'E'-numbered Harlan Sharp rockers with his TF 240s and they weren't very good, geometry-wise. With...
:rofl:
Yup, guilty as charged! Everyone that sees my car and asks gets told it's "just a 440, not much hotter than stock. I just put loud mufflers on it"...
The TF240s I recently got are perfect. In fact, all the sets I've seen have been as well. That said, anything can happen with any product and it's...
Well this is an old thread and 'mopar65' I hope ya got it fingered out by now. I just noticed this part in the highlight above, and maybe it was...
Big block....drillings from the water neck would fall onto the garage floor and no water flows in the intake but you guys knew that. Besides...
Gotta love them German Shedders. We're down to one and a Boxer chewtoy. [ATTACH]
You could connect directly to the body, I didn't like the cheesy factory clamp (B-body) so I threw this together..a piece of steel braid clamped...
Hmmm that page shows plunger travel as .146 +/- .002....... How do you set at .150 a lifter that only has .146 (or .148). They say "1 turn"...they...
Thanks for taking the time to come up with something usable! Dream it, do it...:usflag:I take back everything I ever said about guys from...
