Separate names with a comma.
I assume all three are set up for standard 59 tappet angle?
Is there a reason you want a 1.7 ratio rocker arm so bad? The Edelbrock Magnum head is currently available, accepts Chevy style stud mount rocker...
There is not much going on lately to read. Can you provide a brief description of how and when this block was used in its previous configuration?
We had a good safe road as well here in Michigan. This one was an entrance ramp onto I-94 freeway, but they built it really long and two lanes...
Also, do those conversion mounts still require the use of the rubber engine mount insulators? I don't see them in your pictures.
Is that manual steering box original to that 67 Barracuda? Pretty sure that steering box is different than the ones I have had. The top cover is...
Can you give any more details on these blocks? What kind of builds were they used for, and what are they going to be used for? Just curious as we...
He cannot use a B&M flex plate because he is keeping the stock Magnum fuel injection. The 5.9L engine will require the matching 5.9L balanced flex...
A light duty basic 1500 2WD could have a 42RH with 5.2 engine. They were not as common, but they are out there. As moparmat2000 said, look at the...
Pretty sure Ansen made the Mopar Performance covers, so I would expect the paint durability to be the same.
That is fitting better because it’s not a 46RH. You have there a 42RH or A500. It is smaller like a 904 trans. You will need to know that if you...
Was this intake tested on the head you are moving the pushrod over with offset rocker arms?
Looks like Ansen USA is now offering cast aluminum valve covers for Magnum 5.2 and 5.9 liter engines and they currently list them with grommets...
If the spark plug wires were routed incorrectly with numbers 5 and 7 right next to each other, the number 7 cylinder would supposedly be...
Kind of looks like the deck was not flat front to rear, but also maybe twisted, or lowest at the top rear area? Maybe I am not seeing it right....
At 20 seconds into the video from post 57 I think I can see a push-in style breather in the right side valve cover. If so, there is no way your...
The counterfeit problem is "supposed to be" mainly happening from unknown sellers like those on ebay. When you buy new name brand parts from...
The stock dampener bolt is just long enough to bottom out in the crank and damage the threads on the tip of the bolt if used to turn the engine...
I wonder if Milodon sources out these pans to different vendors that actually make them? Your old pan has one style of baffles. Your new pan has a...
What part number is this oil pan?
The best way is to physically measure the clearance between the lifter plunger and the retainer ring or snap ring. That is what you are actually...
Do you know for sure the reason these used heads had some bent valves? The Engine Quest heads were really castings, but a lot of them were sold...
I have a 4.38" bore and ordered the 4.41 Cometic gaskets for mine. The one thing that surprised me was the bore shape. I assumed they would be...
Any chance he took a picture of the starter? Curious to see the nose cone area. What we are calling mini starter is just the Nippondenso based...
That cup is steel, isn’t it? Weld it!
If you are using the fabricated valve covers with no scallop near the alternator, you will to dent or modify the valve cover. If you get the...
A non A/C bracket does NOT move or rotate the alternator at all. Exact same position. The idler pulley location was moved up and toward left side...
Definitely did not start out as a performance head, but still a decent option for stock Magnum engines. Thanks for posting all your results on these.
Apply some penetrating oil like WD-40 and use a twisting motion while pulling up. Twist back and forth as much as necessary. Slip joint pliers set...
I am running a Mopar conversion kit, distributor, and orange box. I never had any troubles with this setup yet, but I bought the kit new in the...
