Separate names with a comma.
welcome from across the valley!
yep, it is a good idea to replace the pinion bearings while out if you don't know when they were last changed. (Although I have run used ones...
to clarify, this was originally a 318/904 car. Here is the fender tag and also some closeups of the rust I mentioned in the first post.[ATTACH]...
PRICE DROP - $8,500
did you find one yet? I have one that needs side gears, and the bolts that hold the 2 sides of the case together (no idea what happened to them)...
Jim, is that a B or an RB? It also depends on valve covers, I tried some aluminum ones but they would not fit, my stamped steel are a bit shorter...
RB in a barracuda, you will most likely need to change the heater motor (Napa has a smaller diameter and shorter one) and if you have power...
I originally wanted to drop mine in from the top as well, but followed advice on this forum and dropped the k-frame instead. On the plus side, you...
you are not disturbing the pinion depth so, you should be fine setting the backlash correct and checking the pattern. I have done a few that way....
I put the engine and trans combo with the headers on already onto the k-frame and then lowered the car onto it.[ATTACH][ATTACH]
69 Barracuda fastback, (67 grill and hood) 440, 727 (14,000 on freshened up engine, rebuilt trans) - engine and trans put in 5 years ago. Car...
still sounds like a bad ground somewhere, tail light or parking light.
I put the 440/727 in from the bottom on my 69 Barracuda with no help, not sure I'll ever try to take it out from the top.
congratulations! That looks like it will be a lot of fun!
country style pork ribs (or go get carnitas, less fat!) cut into chunks no larger than 1 1/2" thick, however long. Cook on my Weber with Mesquite...
it depends on the rear end ratio. Most with the skinny tires were high ration for the street and most with fat tires low ratio rear for the turf...
also depends on the temperature where you are spraying. As a general rule, lacquer does not lay down wet, you need to cut and buff it. Also, there...
you can get 4 1/2" diameter cutoff wheels for your angle grinder from Harbor freight. They do a pretty good job cutting through 1/4" material. You...
6-point snapon would more than likely get it off, too bad I am not closer, I'd bring some over and take it off for you.
I just used the el-cheapo harbor freight furniture dolly for 8 bucks. It held my 440/727...
saw this down in Mississippi right after hurricane Katrina.... Antique car? and the old strap-on hitch! LOL
So... last night, I was sealing up valve covers and dropped my socket when tightening the rear bolt on the drivers side. I listened carefully for...
maybe powdercoating with a satin finish? Or is that more of a brushed finish? I can't tell from the pic. Either way, if you take steel wool to the...
praying for you....
I had a 57 chev shorty wagon in the mid 80s. built 307, 11lb aluminum flywheel, and 4 speed... the only race I lost was to a bike (Honda 750). I...
try a different coil? I had one that only had a miss at a certain RPM... swapped the coil out and it went away....
just read that thread... great info! Thanks, ir333!!
I have them in my 69 Barracuda with 440 and power steering (MSD mini starter). I just removed the driver side to replace my steering box. I was...
Bob, I already have the steel shim gaskets in it now..... reading, it looks like 1 point is ~4% increase in HP.... not sure about torque... so, if...
Thanks, I am aware of the work and needing to have it balanced, and I already have the MP steel shim gaskets in it. By an increase of one point,...
