Separate names with a comma.
I got the sales invoice for the 390hp crate.Is there options to have a headshop enlarge them exhaust ports? That’s what the prior owner said...
Yes, for the most part. But I think they actually care and seam like good guys. They kept the orginal 10 or 12 gauge power wire running over to...
I can't recall ever seeing a factory alt wire have a fuse and the power master instructions didn't mention a fuse. Would you want the fuse close...
Or maybe I actually did discuss with them the route. To include asking that better quality wire be used and to call me if the supplied cable...
The 390hp crate came factory with 2.02. So I don’t know if that’s what he was talking about.
Does anybody have a chart or diagram of grounding points?
Check the common ground point. A little corrosion can cause headaches. 2nd would be the switch.
Had my one wire 170amp alternator installed today at a local hotrod shop. I wanted to give them a small job before sending them any big tasks....
The largest MOPAR Magnum heads and prior owner said they were machined for 2.20 or 2.02 exhaust valves. Idk if that’s even possible. I can...
Most stock PCV valves have a poppet weight and aspring acting on it, at the beginning of it's travel. The vacuum will lift it off it's seat at...
Stock PCV didn’t open up enough or ar all with the large cam low vacuum at idle. I had 7” of vacuum at idle.ME Wagner has adjustable low flow...
ME Wagner. Excellent instructions included with the product and website.i was right at the low vacuum setting of 6-7 so I used low idle spring...
Oil psi is now good. The fuel injection IAC needed reset to hold better idle. Install dual flow adjustable PCV valve. Adjusted roller rockers....
Emailed Randy with Harland Sharp. He said to not worry about my 15psi hot idle oil pressure on pedestal mount roller rockers.He is looking at...
Harland Sharp mentions that their needle bargains allow for more oil flow to the rockers. More flow = less pressure.
Harland Sharp has this note on the LA V8 Special Notes: * Needle bearing allow for more oil flow to the rockers. * Oil restrictors may be...
The 360 crate 390hp came with Hydraulic Roller Camshaft - 288°/292° duration, 0.501"/0.513" lift. Prior owner said he had a larger cam put in....
over 30psi
Long tubes are typically lower and will cause some issues on driveways or speed bumps. "race" is often larger tubes which come closer to...
I see what the prior owner did. He found a wide enough grommet that mostly fit and he used black sealant to hold it in. Instead of using the 2nd...
Current setup has a small PCV on the valve cover passenger side rear. Front passenger side has a plug grommet. Driver side rear has a grommet...
Doing both. Fixing what needs fixed to enjoy the car and if I get offered a good price I will sell it. This is my first Barracuda, I actually...
Bumping into a old thread. I needed this tip, thanks. I was able to use an extra wrench and a small MAPP torch. Bent it right to shape....
That makes sense. Comparing the roller rockers and roller cam to modern engines; those guys often report 10-15psi at hot idle.Prior owner...
No. Cheap aftermarket voltmeter.
Mechanical gauge installed. 65 degrees outside. Startup idle 65psi. After two cycles of the electric fan kicking in and off the hot idle psi...
Im not using a filter adaptor. Later on I want to do an oil filter relocation.It had a short Fram filter in the stock location. I used a...
Running Mopar fuel injection kit. PCV hose goes the backside of the intake manifold under the throttle body.
On a 80 degree engine I got 140psi on every cylinder plus or minus 4psi. Thats is pretty good, correct? It's been years since I've done a leak...
Looks like the to the rear of the intake manifold.
