Search results for query: *

Sorry about the mis communication! My wiring harness is from a non AC 68 dart. the blower switch is is a 68 dart with wire harness. The resistor plug is different Can it be made to work? Harness is non Air 68 harness Resistor board is 2521409. Any help would be appreciated!

The plug on harness are different. Could I change resistor boards or change wiring or plug receptacles. The motor has been checked and new brushes installed! Could you give me a solution. I am well versed in soldering! Thanks!

I am using a 68 dodge dart used dash wire harness. I have a 69 heater motor but the lplug receptacles for the my motor is different. I have wiring diagham for 68. Basicly they have different plug ins to resistor board Can this be modifed to work? Your help would...

Your help would be appreciated! thanks!

Thanks for the replies! I called centerforce. They said it might take 3/8s to 1/2 in. release to push in fingers. I hope this is it. Thanks for the info!

NO! I think I will need to adjust clutch rod adjust=ment rod?

Gentlemen! 68 dart 360/833 change over from auto. Everything mew/rebuilt from Brewers with all new component z/bar fork,pedals #734 bellhousing//hurst comp new shifter. Everything bolted up right. Clutch new 10.5 23 sline disc centerforce street clutch. Clutch disc would not release when...

Any one have problems with clearance problem next to 90 degree oil filter&pass. side down pipe? These are stock 340 manifolds and are correct as I have owned 2 cars before. The rest of system w/ H pipe installed with no problems. Seems like down pipe is resting on my oil filter...

Anybody have fitment interference on pass side 68 dart 340/360/j head down pipe hitting oil filter side w/90 degree oil filter clearence? Mine is very tight looks like I might have a leak. Any info appreciated!

Red Line hub caps! I will enlighten you guys as I am a old fart. Purchased my new 1968 gts 340 auto the last of Dec. 68'. Car came with small red line caps. I will say it was a very late build. Just my 2 cents.

Thanks guys. After studing it that makes sense!

I am ready to install 360 motor & 4spd together. Was checking some clearances at tunnel area. Looks like I will have to unhook the rods from shifter to get them by cross member. Everything is new from Brewers. What is your wisdom? Photos enclosed,D dog!

Caliper Switch! I switched sides as everyone said. It looks good to go. When I started build I ordered parts for 73 up dart, big bolt pattern. I also ordered hoses for 1980 diplomat! Hoses bolt up good. I will probably put camero hoses on later. Setup should work nice with small bore...

Guys! another photo! I am reason from coments that reverse caliper so its on top then bleed? Get camero hoses from Dr. diff and should fix problem! Please comment! Your help is appreciated. D.Dog!

Can not get get solid pedal when bleeding with helper. 3 - 4 pumps then pedal is solid. Push down good pedal. Let up pedal goes back to floor. Can find any leaks or air. We have done this 3 times. Everything is new. 15/16 master, lines calipers,pads slider system 10" rear...

I just received my radiator today and it has outlets on wrong side. It is a 23 74s. Not what I ordered. Outlets are on wrong side. Ordered over phone and explained what # I need. He sent me wrong one. I ordered a 1635S with center out let & bottom drivers side. I am not very happy. Did...

I think 273 dart is correct. I think it goes to wiper harness. I don't have a wiper washer on car. According to my classic diagram thats where it would connect to. Thanks for your help!

Its got me stumped!Acording to engine diagram 1 brn wire from ignition to fire wall plug then to ignition resistor which is in a different cavity on same plug. This electronic harness came from Evans last year. This other brown wire has a plastic plug on end. If it goes to starter solenoid...

Need some wisdom on my electronic conversion harness from Evans. Its for 340 V8. There is a brown wire from new plug in which is fairly long with plug on it. My wiring diagram is is from 68/69. I am also changing car over to 4 spd. Does it go to a neutral safety switch. Photos...

Thanks for the info. I will look into it!

Rebuiding my 68 dart w/ 83/4. Moved rear end back 1" with 3/4 inch inboard kit. My new monroe shocks won't fit. The angle to great to fit on bottom mount! Would I have modify rear shock mount or is there another shock plate that might work? Any ideas would be...

Maxwedge 470! Just seen your post! I have not been on in a few days. Anyway I would be interested in just hood. I will make reasonable offer I am not far from you there would be no shipping. Send me your phone # if you want to dicuss. Thanks

Send me photos and description & price! Thaanks D dog!

I have two ignition switches. I want to use my 68 because I have a really nice main harness. The 68 has 6 plugs but only has 5:? Could someone clarify. See photo thanks!

Would like to be driving distance from central Mich. Any help would be appreciated!

Thanks for the measurement. I had to buy new ones!

Could some one send me a measurement for pass side distance from door edge to 1st letter G of GTS emblem for a 1968 GTS dart! Thanks. Any help would be appreciated. D.dog

Jim! my address is: Dennis Vallance, 7595 South Whiteville Rd. Shepherd,Mi. 48883 Thanks for your help. Do you need any $ ?