Search results for query: *

  1. gliderider06

    the USS New Jersey battle ship.

    New Jersey made it to her dry dock. Not my pictures however. Last photo is BB62 and BB64 from late 80s
  2. gliderider06

    the USS New Jersey battle ship.

    Honestly, I thought the Missouri and Iowa were already stricken from the Navy records leaving the Wisconsin and New Jersey still on the Navy registry. Funny, during the ceremony, it was mentioned thT while the New Jersey was in dry dock, the navy was going to take it back for recomissioning...
  3. gliderider06

    the USS New Jersey battle ship.

    It's nice to see the drone footage of it. There was less than 6 foot of clearance between the upper mast and the bottom of the Walt Whitman Bridge. They stopped traffic on it as she passed through to avoid any car accidents while doing so. What a beautiful and majestic ship.
  4. gliderider06

    the USS New Jersey battle ship.

    It is somewhat. $250.00 per person with restrictions. <16 not allowed and need safety boots, hard hat etc... I might do it if I can get a free day on one of the weekends it is open for tours.
  5. gliderider06

    the USS New Jersey battle ship.

    I got to see her yesterday. Such a great experience and I hope to do a dry dock tour as well. I was going to create a post, but... Here are some of my pictures.
  6. gliderider06

    Pictures in the classified section

    I missed a few days, but the upgrade to pictures in the classified section are amazing! Bravo to whomever's idea it was. Now, I need to spend half of my morning scrolling through all the ads now.
  7. gliderider06

    [FOR SALE] Hood pins

    $9.00 plus shipping
  8. gliderider06

    [SOLD] Clip sets

    $20.00 shipped
  9. gliderider06

    [FOR SALE] Small block 3 piece K.D. set

    $135.00 shipped to a US postal address
  10. gliderider06

    [SOLD] Clip sets

    $21.00 shipped to a US postal address
  11. gliderider06

    [SOLD] 4 hole carb spacer

    $23.00 shipped to a US postal address
  12. gliderider06

    [SOLD] HOLLEY 700cfm double pump carb

    $200.00 shipped to a US postal address
  13. gliderider06

    [FOR SALE] Small block 3 piece K.D. set

    Small block 3 piece kick down linkage set. Was for a 2bbl, but can be easily modified for a 4bbl. Asking $135.00 plus shipping charges
  14. gliderider06

    [FOR SALE] Hood pins

    used hood pins. Missing one pull pin Asking $10.00 plus shipping
  15. gliderider06

    [SOLD] Steering couplers

    I have 3 steering couplers. 2 are .60" shaft and 1 is .70" shaft Asking $5.00 each plus shipping
  16. gliderider06

    [FOR SALE] Brake pushrods

    I have 3 brake pushrods. 2 with the bolt and 1 without. All 6.5" long Asking $10.00 each plus shipping
  17. gliderider06

    [SOLD] Oil/trans cooler

    Used 3/8 oil or transmission cooler. I have no use for. Asking $25.00 plus shipping
  18. gliderider06

    [SOLD] Clip sets

    I have new brake line set and wire harness clip set that's unopened and a partial 3/8 fuel line set. Asking $23.00 shipped
  19. gliderider06

    [SOLD] Small block airgap intake

    Brand new small block, Chinese airgap intake. Never installed. Asking $130.00 plus shipping charges
  20. gliderider06

    MSD distributor tuning

    ...and one silver light. Revved it well above anything that I would ever be driving it. I dont have a tach, but it was screaming. Guessing well over 3000. My dial back timing light never went past 30* I think I need to go to the light saver and blue springs and hope the timing gets closer to 36*
  21. gliderider06

    MSD distributor tuning

    ...timing light for this to check against my old, non-adjustable one and both read the same. I revved the motor pretty high and would not go past 30* . The distributor is relatively new <5000 miles on it. I think it Is the springs, but I do have a set of weights that I can swap if needed if...
  22. gliderider06

    MSD distributor tuning

    ...with the springs. I tried this before with the edelbrock and the valves pinged badly and I put the heavily spring back in. With the new Holley, I think I will be able to get away with it. Actually, it would ping at 10* when I ran the edelbrock carb. One of the many reasons why I switched it out.
  23. gliderider06

    MSD distributor tuning

    No I have 15 initial and another 15 Mechanical. 30* total. Will not go higher until vacuum is applied then goes to 50*. I replaced the blue bushing with the silver and I got more total timing now, from 44* with vacuum advance. This is why I think the heavy spring may be holding me back.
  24. gliderider06

    MSD distributor tuning

    I forgot to mention as well. Anything over 15* initial the thing will ping when hot when giving it a slight push on the throttle. I'm using autolite 64 plugs. It helps reduce the detonation. I recently changed from a 1406 Edelbrock to a 650 Holley spreadbore. Just by doing that I was able to...
Back
Top