Separate names with a comma.
I bought a Quick Jack over the winter that can raise a car 24". Ok, great, but the frames block most of the side access. I was removing and...
I do care. Glad to help out when I can.The standard 14" wheel on SBP Mopars was only 4-1/2" wide. The "big" 5-1/2" wide wheel came on HP and HD...
This is my 200 series 64 Valiant. It didn't run when I got it but I rebuilt the 225, put the 3 on the tree back in and put 10,000 miles on in the...
Turnout was about half of normal. One of my Barracuda Buddies did not attend because his 67 FB has a 380hp crate 360 and 3.91 gears. He figured...
Remove the window winder and arm rest if your car has them. (Rear arm rests not standard on 68 cudas but part of the Deluxe interior) There are...
Are there any upholsterers in your area? A good shop can do what you want. I agree that example you have looks pretty good.
The inner fenders are spot welded to the top of the shock towers in that location.Check the frame rails carefully. They rust from the inside out...
I recently pulled the trans out of my 64. I used a 2 x 6 x 57" long piece of wood. A 2 x 4 would be strong enough but I happened to have this on...
I recently needed to pull the 4 speed to take care of a couple things. I keep the 64 at a female friend's house so I'm constantly shuttling tools...
I just did this on my 1964 /6.One thing to note, john6464 installed his bearing backwards, the lettering should face out because there is a lip...
The subject of what carb to use on a /6 seems to come up often. This is a factory training film that shows proper adjustment of a Super Six BBD...
Female friend let's me keep my 64 in her garage. Her old washer that came with the house quit and she wanted new ones. We went appliance shopping...
Good to see you out enjoying your cars!I just read through your posts. Looks like you have everything sorted out.If you still want to pull...
If the weather is good, they usually get 400 Mopars. It's well worth the trip if you're within a couple hours drive.I'm pre-registered and will...
Thanks for your reply! I think I'll start a separate post about my dilemma as I don't want to hijack this thread. Short story is after getting a...
It's in my 68 Barracuda and the spare tire cover sits flat on the floor.Note that earlier Cherokees had a 4.5 bolt pattern and matches my...
@JimMacHow did your install turn out?
If you have 20 minutes to spare, I thought this was a pretty interesting take from a designer's point of view. Maybe it's the black exterior but...
You didn't say what bolt pattern you have. SBP use 7/16 studs and 3/4" across flats nuts. LBP use 1/2" studs and normally 3/4" AF nuts. BUT, there...
A legitimate Mopar show won't allow you through the gate. Sell the LS and buy a 5.2 or 5.9 from a junkyard RAM if you "need" a V8. If you go GM,...
IIRC, Doug Dutra has a very nice detailed write write up in his Slant Six book.The book came out after I had rebuilt my 225. Having said that,...
It has a rack and pinion mounted in place of the standard Mopar worm and sector box. The normal struts were removed to make room and those others...
There are lube holes in the rocker shaft approx 1/8" diameter. One for every rocker. The 225 in my Valiant had been parked for 32 years and every...
The trans tunnel is NOT centered in the car. It is offset to the right about 2". I put buckets in my 64 Valiant and had the same concern. I just...
@jonn6464 Would you happen to have the P/N of the bearing you used?
FWIW. With 3.23 gears and standard diameter tires, I'm running exactly 3000 at 70 (GPS) mph. My speedo is dead nuts accurate too.I cruise the...
I was born on a Sunday, just not last Sunday.
I've read all the responses, thanks!Yes the car creeps a little in 2nd gear with clutch in. Yes it goes into 4th gear with pressure on the stick...
Thanks for the advice AJ and Duggie! I'll do some testing when I visit the car later today or tomorrow.I took it around the block about a week...
My original plan was to convert from 3 speed to 4 speed as economically as possible using that swap meet 65 trans with factory parts retaining the...
