Separate names with a comma.
I too would like to obtain a cylinder balance tester. I still don't trust insulated plug wire puller pliers. My slant has HEI conversion and my...
Yep, I'm prepared for sticking quickly. I've done floors and it does stick well. Thecleaning of the ceiling is coming along. I sure like the...
Thank you sir. I now have confidence that it'll stick and stay. By the way, the picture of your floor Fixmat installation went well and was well...
I read in this thread that you planned to install Killmat on your roof panel. One thing I would like to know is, in the heat in summer, does it...
Damned if I never considered this. I'm 14 years retired from a Colorado state vehicle emissions testing laboratory. This was not a state...
Thanks to all for setting my mind at ease. I went through thinking about this years ago and my conclusion was the same then. Cone shaped lug...
I've been looking at the Mopar Action magazine article. I understand the concept but when the tapered seat lugnuts are torqued on the wheel, what...
If I get a successful front end alignment from a local shop I'll be staring at a headliner install, possibly/probably by a local upholstery shop....
We too have had many many cats over the past 35 years. In our experience, if the cat is treated respectfully and with kindness there will be no...
I'll just figure it out. My wagon spare is a big bolt circle 14" mopar wheel. When I take the stands out I'll be able to get to the spare and...
Oh rats!! I didn't know about 13 inch wheels having smaller poverty caps. Any old poverty caps are sorta rare so I have an additional hunt...
Thanks for the info on poverty cap diameters. The caps that came on mmy Dart were on the13 inch wheels and look small to me, but I've been...
I just ordered studs that are .005 larger knurl diameter, 3 inch length. Sounds like I may not need to shorten them to clear my dog dish caps....
Thanks for the response. The stud did not protrude at all. With the nut tightened on the wheel I could look into the nut and see three to five...
Thanks, I'll go for it! Jerry
3 or 4 years ago I installed a disc brake kit on my '63 Dart Wagon, /6 and three on the column. The rotors are about 11/16 thick at the stud...
I have been feeling that the device may have given the ecm a rich condition in order to make it drive the fuel delivery lean. Silly idea since...
I'm suspicious too. The fuel/spark control systems of today are pretty well programmed to get most of the energy from the fuel into motion....
I too am a 71 72 Satellite guy. 72 for me 'cause I like the tail lights. Don't care about drivetrain. Weird but a slant 6 with 4 speed. A...
Thanks 72. That chart deserves to be copied and put in my Mopar info stash. Jerry
Thanks 72blu. It does appear that there is some other problem that I hope I find with the car in the air. If nothing is obvious to me it'll be...
When I had the alignment done, three or four years ago, the tech told me he got a bit over one degree of positive caster, so it sounds like I'll...
Brake hoses are plenty long. I did the frontend work shortly after obtainig the car. It's going to be in the air soon. Thanks guys
"63 Dart wagon manual steering. When trying to turn to the left or right lock, the effort required seems to quickly increase--a lot. It has been...
I haven't had a Mickeys in years but I liked the light skunky taste. I can only drink gluten free (GF) beer for many years now and haven't found...
I learned cursive in the early 50's. In USAF in 1965 I was sent to Russian language training and after learning Russian cursive my English...
Will the gel type super glue remain somewhat flexible after setting up? Or does the gel type adhere best to the rubber? I suspect that the two...
Yes, I'm not happy with the silicone idea. Silicone would seal from water leaks but won't hold anything together. Super glue sounds like...
Thanks for the suggestion of Laysons. I ordered seals from Laysons. The seals seem to be made in the correct cross section profile. Each one is...
