Separate names with a comma.
similar rear frame used for airtemp control. they had a light that bolted on in a holder, powerd off the dash lights or column shifter quadrant...
i think you have the red switch and you need the grey switcheasy to say when i'm chugging coffee and bored at work but looking at the helpful...
if its anything like a Right hand drive one. it has a rubber bush that is pressed in or that you press in. The bush is much like a lower Control...
OK when you say shim are you talking literally about a very thin pice of spring steel or the metal brake pad backing?that looks like the brake...
you used to be able to replace the electronic module with a pull type mechanical set up and a big pull actuator in the dash said choke and...
even slant 6 cars in SA and Austrlia got them....more to do with the use of the car than power or torque . if you drive like the dukes of...
if its manual it will be orginally filled with a water resistant grease feel free to try pumping more in. or just do as most do... top off the...
The exact reverse of what it says on the sheet, and what is indciated i think on the bushingsWhat you want is the narrow side of bush pointing...
the aussies also make bushes mackay rubber A1170 lower fits all mopar A bodies RBK1170 for a kit of 2A1081 for uppersMackay choose...
yup its right get some nice seals like orginal not balljoint boots. they just come off
I just wouldnt take a loom out of a car. did it once and regretted every minute after. unless something has shorted out and melted huge chunks of...
take off cover hammer the flange flat put back on with new cork... glue it to the cover if you wish with a light smear of sealer do the little...
an Australian 4 speed would go in.... designed to fit the auto tunnel in an A body... they only had 1 tunnel/floor pressing, so their...
The symptoms are exactly what you get if you have more than about 5 degress toe out... all applied on 1 side. massive imbalance in track rod...
You have a massive toe out on one wheel.. if you get that rectified even if camber and castor are totally wrong it will stop doing that "raising...
i thought the bolts were a more or less universal standard...i.e what fits my valiant fits most other cars of the era. and potentially...
if you have a old starter (just in case you break it) that you can use. do the kick back test. set initial timing to 5* BTDC start motor. stop...
many thanks, i have now gone to the article.... can't get there from work PC due to some kind of dislike of my UK based address.... but i can...
Are the FMJ spindles taller?i could see some benfit there... kinda like lowering your car without lowering it in rspect to the roll centre...
old style MSD6 AL and derivatives with decrete components rather than the machine solderd ones of today occasionally corrode inside the...
2 sizes of pitman arm as well. although ive never tried it i'd guess the big spline pitman might fit on a small spline manual box and end up at a...
not sure if appropriate here but using Moog k750074 (ford truck part) trim the ends off the lower thread get the ones with grease fittingsuse...
got a throw out bearing off a jeep...fits the IBR but no idea yet if it fits the fork, thats still on the car and it school prom season so no...
yes just be careful not to connect up the old wire again.... if the short isn't visible in the run in the engine bay it going to be at the...
you can see it in this onethis is mine and on this side is standard on the other side the stud was snapped, and i never reailsed for a few...
even if it doesn't normally, and i don't know... perfectly viable place to take it from or (indeed off the only live when starting, starter) ......
this miight be ueful for anyone who doesn't want to spend a lot on aftermarket partsthe aussies went racing with their valiants in the 70s...
if it is did you set the choke flap again... i presume you had to undo it to take the carb off. it should hang a "bus ticket" thickenss open...
if its your dome light that is the problem...you may find the wire up the screen pillar melted....if so do not pull them out whithout tapeing...
IGN2 power to igntion/coil when key in start START is power to starter relay when key in startyou need these 2 to start.... 12 volts at...
