Search results

  1. drewmac

    dougs headers dont clear zbar clutch linkage

    Sorry for posting on am old thread but I just ran into this issue. Aside from moving the arm over and revesing it; is there a specific angle it has to be in relation to the arm that connects to the pedal? Like arms on a clock?
  2. drewmac

    Borgeson steering

    Yes I had the same problems with my Borgeson/ D453 header combo. I had to beat the snot out of the header to dimple it enough to get both in with some clearance. The headers also hit the drivers side Torsion bar (.96 dia) and the passenger Tbar as well. Such a frustrating install to be honest...
  3. drewmac

    PST 16:1 Box excessive play

    Got it this morning. Thanks James!
  4. drewmac

    PST 16:1 Box excessive play

    Yes. I'll PM James.
  5. drewmac

    PST 16:1 Box excessive play

    Still waiting for some kind of correspondence from PST on my box. Been a month or so.
  6. drewmac

    Combo steering column

    Thanks guys. This helps a lot!
  7. drewmac

    Combo steering column

    Can I use a floor shift upper (part right under steering wheel) manual column on a column shift ( below the rotating part with the lever) lower power column to make a floor shift power steering column? I have both and was hoping I could mix n match them to make what I need. Sorry I this is...
  8. drewmac

    67 cuda steering wheel

    Thank you.
  9. drewmac

    Tuff Wheel / manual steering

    That carbon dash is awesome!!
  10. drewmac

    67 cuda steering wheel

    Where did you get that cover? I'd love to find a black one.
  11. drewmac

    PST 16:1 Box excessive play

    Yes. I have a return invoice. I'll PM you the info.
  12. drewmac

    Hey bud I saw you had the same issue as I did on the PST box. Going to send mine back and...

    Hey bud I saw you had the same issue as I did on the PST box. Going to send mine back and hopefully get a new one.
  13. drewmac

    PST 16:1 Box excessive play

    James I have a return invoice for a problem just like this. Should I just send the box back still and await a replacement?
  14. drewmac

    PST 16:1 Box excessive play

    I have the same exact problem with my PST box. Sending it back to them.
  15. drewmac

    Replacing power steering with Manuel steering

    Are you looking for a 23:1 or 16:1. I am going to go to power steering this fall so I will have one of each avalible.
  16. drewmac

    What power steering pump was factory for a 68 Barracuda Formula S-340

    Cast Iron. Doing the Borgeson conversion and need the pulley.
  17. drewmac

    What power steering pump was factory for a 68 Barracuda Formula S-340

    Autoxcuda do you know where I can get just the pulley for the saginaw set up? Do they repro them? I am going from manual steering to power and have everything but the pump pulley.
  18. drewmac

    Replacing power steering with Manuel steering

    Thanks Man. Have a good one.
  19. drewmac

    Power Steering Conversion

    Going to email you.
  20. drewmac

    Power Steering Conversion

    So could I just put a PS shaft in my manual column and bolt PS in?
  21. drewmac

    Replacing power steering with Manuel steering

    Guys I don't mean to hijack the thread but I have a quick question for you. I am looking at doing the Borgeson conversion. Do you know if I can use a power steering shaft in my manual steering column body? I'd like to do that if possible to keep it a stock as possible. If I have to go to a power...
  22. drewmac

    273 Commando ignition wire question

    8mm would work. Tight fit but such is life.
  23. drewmac

    273 Commando ignition wire question

    X2 for 8.5 wires!
  24. drewmac

    273 Commando ignition wire question

    Man that is awesome!
  25. drewmac

    Pertronix for dual point distributor

    Ok. That is doable. I'll keep it as is. Thanks.
  26. drewmac

    Pertronix for dual point distributor

    I have an original dual point from my 273 Commando. Can you convert it to a Pertronix 2. also does anyone have or know where to find a rebuild guide/ instructions for that distributor (If I can't convert I'll rebuild it and sell)? It is just like the picture below I got off the internet.
  27. drewmac

    Mystery Ignition Box

    I wonder if you take it off and look underneath if it will have some info there like an MSD box does. If you change to a Mopar type go with a FBO box conversion. I just put one on my 67 and it is fantastic. Has a rev limiter and made in Oregon. I changed from an orange box to this and the...
  28. drewmac

    Console....

    I know this is n older post but anyone ever put a b body console in your a body?
  29. drewmac

    [FOR TRADE] 1965-6 DS Commando valve cover

    It is the one with the breather cap. Not with PCV.
  30. drewmac

    [FOR TRADE] 1965-6 DS Commando valve cover

    I have a 1965-6 273 Commando DS valve cover in very good condition. I need a 1967 DS valve cover to match the year of the car and PS valve cover. Willing to trade for one in like condition. Needs to have the 1967 "W" type wire holders.
Top