Search results for query: *

I'm looking for an A 230 bearing retainer part number c97728. Its a 5.125 diameter. Brewers has it for 90 bucks "reconditioned" with seals and everything but I was hoping someone had a used one for cheaper???

Anyone have experience with the avenger series of carbs? not on a mopar but looking for advice. ford 351 Cleveland 4 barrel heads (which essentially have big block sized ports) cams like 550 lift, eddy intake i forget which one exactly. Basically just simple bolt ons. It sat for a while but...

If I drive around for a half hour or longer and get the car good and hot, then shut it off and go into 7/11 or something and come back out I have to hold the throttle open a bit and it takes a few seconds to start. It smells like gas when I shut it off too. Its an eddy 600 cfm. Could my floats...

My FABO sticker got messed up somehow, most likely a freak accident on my part. Joey sent me out a brand new one to replace it! great guy thanks a lot!

Anyone know if a 1970 B body radio would fit in place of a 73 dart radio? I saw this awesome radio in classic industries that looks so much like the A body one. Just wondering if it would fit or if it is way different. http://www.classicindustries.com/mopar/parts/mb2096.html

Is there no reasonably priced adjustable advance distributor out there to work with the mopar ignition? Or do I just need to get one of those cheap hei ones and just run hei ignition instead...

So, I bought this for 2$ at the car show today. Is it anything special? Can't find any online that look like it.

EVENTUALLY Id like to put a nice radio in most likely having two amplifiers. My stock alt just took a crap. Cheapest stock alt around is 54 bucks. I saw a few guys using these 1990s denso alts with out a/c. 120 amp unit. Found on on ebay for 75 bucks to my door...

I think the side cover is the interlock style.

Part Number: felpro 90109 http://shop.advanceautoparts.com/webapp/wcs/stores/servlet/product_intake-manifold-gasket-set-felpro_5184444-p?searchTerm=intake+manifold+gasket#fragment-4 There are what look like 4 small O rings with this gasket set. where do they go and what are they for? I'll...

I have a under dash reverse light, wondering where the one wire went to from the factory? any help is appreciated:burnout:.

Mopar Muscle Cars - Lebanon - YouTube

I've got a 72 dart grill I am going to paint. I'm not looking to go crazy and do it 100% exactly like mopar did. Was the factory closer to flat black or semi glass?

Engine specs: 318 fresh re-ring and bearing done by me 360 heads no milling whatsoever on them 340 spec camshaft headers torker II intake Eddy 600 carb electronic ignition w/ orange box andstock distributor with light weight springs I went out today to screw with the timing a bit...

Is there a common point of failure on these am radios? anyone ever fixed there own? don't really want to pay someone to fix it, I am sure I am perfectly capable of repairing it I just don't know where to start. I was thinking if I get it working I could pick up an am fm converter and have...

I've got a 73 dart turned Frankenstein. 73 rear bumper, 70-71 quarters and fenders, 72 grill, doors are 73 with no vent window. The front fenders arent drilled for the fender top mount signals, I am debating weather or not to drill them for the 73 indicators I have. So what do you guys...

Freshly rebuilt 318 bottom end 360 heads stock small valves torker 340 intake eddy 600 cfm carb 340 cam headers to 2 1/2 pipes with X pipe I had a running motor in the car 8 months ago. Used the same ignition stuff and carb. At first I had no spark but when i replaced my distributor with one of...

Auto pedal setup from 73 dart. $20 + shipping slant 6 3/4 speed dust sheild set $20 + shipping SOLD!!! trans Crossmember from 73 dart works with auto and manual, not sure what years though. took the spool style mount. $20 + shipping. Will Bead blast and etch...

4 door door panel set, 20 bucks + shipping 4 door rear hinge set, 10 bucks + shipping Steering column #1 (black) out of a 73 dart 4 door auto column shift power steering car. 50 bucks + shipping with no wheel or lock cylinder, 80 bucks + shipping with wheel. Will...

73 dart swinger. Just painted the engine bay so I had everything out of there. key on I have power at all 4 posts of the ballast resistor, power at the positive side of the coil, power at 3 posts in the ECU plug. The only thing I can think rite now is I messed up the connectors over by the...

Just focusing on getting the motor to crank over not worried about starting. I recently painted my engine bay and had everything apart and I also swapped to a 4 speed at the same time. Lots of things to get messed up. Rite now I have everything electrical hooked back up. I put the battery in...

car is a 73 dart swinger that was orginally power disc and auto trans but converted to manual disk and 4 speed using parts from a 76 duster. The brakes are all bled out and feel good just the pedal is high. Its about an inch higher than the clutch pedal. The rod measures 6 1/4 inches from the...

I'm putting a new engine in and I have those cheapy low dragging headers and I am putting a 4 speed in at the same time. I want to know if i can put the Z bar in with the engine and headers in place. I Don't want to put my motor in then realize i have to lift it up or take it out again!

I was at the shop the other day and saw a 94 4runner. To my amazement it had a 4 piston caliper! My first reaction was, those would rock on the dart. Anyway i did a bit of research and it looks possible. The 4 runner rotor diameter is 11.75 If I'm not mistaken you can swap bigger rotors from...

I found these in the garbage. They seem to be worth a bit of money but, I can't for the life of me figure out what they fit. I've been asking on forums, and searching endlessly online. I'm sorry this isen't a mopar part, I am just at my wits end trying to figure out what these fit!!!:banghead: I...

at some point the goo started dripping out of my voltage regulator, it then failed I got a new one. not really the point here. I want to know how to get the goo off? I am trying to prep my engine bay for paint. any help is appreciated.

I need a new temperature control cable for my 73 dart with a/c. I cant find anyone who sells one. Can someone point me in the right direction? I put a used one on a while ago and it doesent work worth a damn. I have the heater/ac box out now so id like to get this working.

Whats the best priced and quality carpet? This is for a 73 dart 2door with a 4 speed. I am mostly concerned with fitment issues and looking to save as much pennies as i can as well. What have you guys got and liked and how much did it run?