Search results for query: *

Does anyone make a shock plate that has a lower than stock mounting stud. I'm running hotchkis spring and would like to gain some shock travel before I blow out my fox shocks. Lmk what you know. Thanks, Keith

If anyone has one to spare, I'd be greatly appreciated. Thanks, Keith

Looking for drivers side 67-72 Abody 340 engine mount bracket 2863445. Would be interested in a set as well(2863445 & 2863443). NOS is even better. Thanks, Keith

Griffin 5-70057 Mopar 26" radiator with AT cooler. Driverside inlet and passenger outlet. 2 row 1.25" tubes. Brand new in the box. Core is thicker than I can use. Core is 2.8" thick instead of advertised 2.6". I'm running aftermarket pulleys and Ford contour fans and there's not enough real...

I have a couple stickers I want to install but not exactly sure on proper placement. Hopefully someone can help. Battery, does this go next to the coolant sticker? A pillar sticker, does this read from the outside or inside. Words out or in? Tire pressure. Does it go above the striker?

Looking for another one of these.

I have a 68 notchback barracuda that was built in Aug of 67. Does anyone know what coat hooks were used? I've been looking for a matching one, to the one that came out of the car, but not sure it's even the right one. Anyone know?

I'm in need of 1 pair of green rear seatbelts. Not sure how I misplaced a pair. 1968 barracuda notchback, if that matters. Lmk

Why would I be getting different readings on driveline angle between the balancer face and the trans out put shaft? Balancer shows -2* @ 88.1 but the output shaft shows -3* @ 87.0. WTH don't I understand. Which is correct?

Are the rear seat buckle clips supposed to be the same color as the vinyl? If so, how does herbs interior dye hold up to the buckle sliding on and off?

I bought a b&m 10230 flexplate. It's supposed to be for an internally balanced small block with multiple patterns for the converter. However, I just took it out of the box and installed it and noticed that there's holes cut in it. I find this odd? Doing more research on finding it's for an...

I've come up empty. Anyone have a clue?

Quick question. I have a purple .557 Mopar shaft running Howard's edm solid lifters. I need to set lash. However the lifters have a bit of up and down movement between the snap ring retainer and pushrod seat. Lash will be .024 and .028. but I don't know if I need to adjust for the up and down...

What's proper procedure for figuring out head gasket thickness in regards to quench? I've seen everything from. 032-.065 is acceptable. I have a stroker 360(414) with forged mahle pistons and forged steel rods. I see people taking the piston protrusion and recession numbers and using the...

So the only thing left to decide on my engine is intake manifold. Bear(bare) with me on this over asked question? This car will be 95% street driven. Maybe a 1/4 pass or autocross once in a while. But it'll mainly be a driver, cruiser and canyon carver through the mountains. So we'll start with...

So I have 2 Chrysler reds here and they are worlds apart. One is very red and the other is burnt orange/red orange. The 90* is the only thing I have that's original Chrysler red, I think. Which is more correct? Thanks, Keith

I need help finding or borrowing Milodons pick up tube for their road race pan part# 18343 I ordered from Summit on 12/8/18, and Mancini on 1/22/19 both have been cancelled. I've tried eBay, Amazon, Facebook market place, Marsh, Craigslist and Glendora Dodge to no avail. I've been getting the...

I'm looking for the D shaft push clip/sleeve for a wiper knob. I believe it's 3/16. Goes inside the knob. Lmk

I'm looking for a coat hook like this one.

I'm in need of this pick up tube for their road race pan. I have the pan but need the pick up. Lmk Keith

Does anyone know where I can get some of these pins? I can't I'd them, I thought maybe Delphi but can't confirm .Anyone have any ideas?

Does this look right? This makes sense in my head. Lmk I'm trying to see how many relays I'm going to need in my electrical system.

I'm looking for a driver's side vent window lower pivot channel in extremely good condition. No pitting, rust or pock marks. Lmk, Keith

Does anyone know if apipco still makes these? I've sent an email and have tried calling numberous times, no answer. Out of stock online. I've found no other sources for purchase. Lmk

I'm looking for front eye bushings for hotchkis springs with 1.5" eye but I need a 9/16 bolt hole. I cannot find anything in poly anyone have any suggestions? Lmk, Keith

Does anyone have a copy of the cam card? Thanks, Keith

I posted this on moparts and in my build thread here. When does money outweigh sentimental value? 1968 notchback build thread Thought I'd post where more could see, in the actual wheel forum. I've have gotten some interest on this set of 18" wheels I had a friend make. So I thought I would pass...

So I have what I think is an issue with the rear leaf springs. They are Hotchkis 24385 Abody springs and they make my car look like a 4x4. There are many people here running this leaf but I cannot find a similar situation. Opposite actually. So my car is a 68 notch. Uscartool inboard 3 hole...

I am thinking about putting assembly markings on the rear housing and center section of my 8 3/4. What would the stamp #'s/codes have been for a 1968 8 3/4 with 3.55 Sure grip or a 3.91. any ideas. Seems like hard info to find.

So I have all new stopping components in my car, which is not road worthy yet, and have about 4-5" of travel in the pedal before it starts to firm up. Brakes are bled, no air, no leaks. Bled using a pressure bleeder, not vacuum. Here's what I have: 68 barracuda manual drum brake car. Frt Drdiff...