Search results for query: *

I grew up with scouts learned how to drive in them. Started in a 62 with 4 cyld 3 speed and then dad bought a 66 v8 4 speed. The 62 4cyld 3 speed was very under powered but would climb the mountains in Colorado in 4x4 low very good. The 66 v8 had plenty of power but loved gas climb anything. But...

I was having a hard time with my 440 challenger hooking up off ofthe line. I put ladder bars on it with the super stock springs that I had on it and the 60ft times went from 1.68 down to 1.30 with a 10 inch slick.

I read a interview with the owners of the Denver track and they stated they were going to build a new track but were going to take 2024 off. Hopefully they don't get lazy on there year off and go through with there plans for a new track in the area.

The I would do it without a welder is to heat the block around the bolt (not the bolt) with a torch and when it is good and hot then spray with penetrating oil may take several tries. Then hit it with a hammer to vibrate the bolt and keep spraying with penetrating oil rinse and repeat. It would...

My question is was it running like this before you pulled the engine to fix the oil leaks or did it stat running bad after the engine was reinstalled? Just trying not to overthink it.

Fred I hate to see the outcome of the trial. I had a daughter do some time and it was hard to deal with but remember he will need help when he gets out. Hopefully he will get out at the minimum time with good behavior. Don't rush on the decision to get rid of the truck he will need something...

We are at 43 1/2 been a good ride.

Congratulation Mark !!!

The one for sale has folding legs

It has legs that fold just fold legs up a bit and slide hoist under them.

I had that problem once and found the water pump impeller had moved out on the shaft and was not close enough to the water pump body. This left about 1/2 gap from water pump housing and impeller which made it not circulate the water correctly. Had already replaced the radiator and thermostat...

Maxcustody: You do you either intake set up will be way cool. Your the one paying the bills and honoring you FIL. I am very happy for you and what you are doing and letting us go along on this journey thank you.

prayers sent your way

Done

At this time it is not street legal. If you would still like pic of int. let me know and I will get some. May have a donor car bought I wqs thinking about getting it street legal.

Has mopar purple cam shaft, 312/590 ross dome pistons, mopar m1 single plane intake, x heads ported and polished, 750 holly dual pump carb, steel crank. Last ime I ran it back in the fall with a little tune and jets it ran low 7.20 in 1/8

Reduced to $10,250

Asking $5,500 but won't sell till after car sales.

1973 dodge dart sport 340 X, heads are ported large valves engine has been balanced, 727 trans with a manual valve body 9 in rear diff with 456 gears with a spool mosier axles, chromelly roll cage, runs low 7.40s in 8th, to much to list, located in Gilmer tx. asking 11,500, car comes with a...

Anybody got a extra 340 bare block?

Need 340 bare block.

PM sent about steel crank

If you will look the linkage has probably came apart. There is plastic bushings on each section of likage. They will rot off and thus no wipers. Word of advice replace all bushings or this will happen again. The bushings are available at your local Dodge dealership parts department.

I guess not to bad for a 340. Never put on dyno. Runs 7 teens in 1/8.

Goes straight as an arrow.

Need some help! My 73 dart has super stock springs on rear but I would like to know if they are on the right side. I can not read the part numbers on the springs. Both sides have the same amount of leafs on each side but the length of each leaf is different from side to side. How do I know which...