Search results for query: *

Anyone using a Holley Street Dominator single plain intake...it has the smaller 318 size ports also....Thinking of using it .... Using a holley performer intake now and wondering if the car will pick up with the this low profile single plain intake. stock 1968 318 .225 @ 50 cam..... .453 lift...

I just finished building my 904 in my 67 Cuda. I worked Saturday 10 to 12 midnight. Sunday 10 to 10. Monday 8 to 3. The 904 works really good .....but will be taking it back out for a couple of reasons. I want to tighten up the clutch packs a little more. I set the rear...

WHATS THE BEST SOURCE OF --ALL REBUILD INFORMATION-- ON THE 904 TRANSMISSION.----CLEARANCES AND TOOLS NEEDED. THANKS FOR ALL INFO.............:thumrigh:

Anybody.................:roll:

What does everyone think the best temp is ---for the best ET.:burnout:

What brand u joint do you guys like????? I need a 7290/7260 conversion joint. 5.527x ...........................i Used a cheaper brand and it's already toast in 6 months. I think a dana / spicer joint will be next. Drag racing and cheap parts don't mix.

Well i went to the track again tonight to try and get some tuning done on the 67 cuda and enjoy some bracket racing also. I took off my 7 blade stock fan and installed my clutch fan --knowing full well -- the motor would be running a little bit hotter.:angryfir: All in the search for a quicker...

509-557 cam in 318?? Has anybody run one of these purple shafts in a 318. What convertor did you run (stall speed ) I am really wanting to run a 4800 to 5000 converter.(9 1/2 dynamic)--with a big duration cam. Thanks for any feed back.............:thumbup:

I will be installing a new american eagle radiator soon and this will let me re-install my clutch fan again. It ran to hot for the steel water pump in my barracuda. *1967 318* The car ran 14.24 at the track last week. I figure, with the clutch fan installed, i should see 14.10 or so in ET. The...

I just bought a new american eagle radiator ae2375 and it's going in my 1967 cuda with a 318 steel water pump.(drivers side outlet) I think it will cool the litle 318 better and will be there for the big block when it's ready......someday. I was wondering if anyone has used this new style rad...

I might put a .474 mopar cam in my 1967 318. I have a 3 grand dynamic convertor and 3.91's and possibly thinking of porting the heads. Anyone ever port a set of 920's................. My buddy has a new home made flow bench all set to go. I already own the cam and lifters and have a holley...

I just bought two holley street dominator intakes and they are in really good shape. I like them because of the small --318 size-- intake ports and are also a single plain intake. Just wondering if anyone has used, or runs one of these intakes. :burnout:

I Might be getting a set of eagle SIR I beam rods. The rods were made in 2002 and lived in a stroker small block for a short period of time. The engine smoked the cam and then was taken apart -- i was told. I was wondering who has used them and if you had good luck with them. ***Please let me...

My radiator started leaking from the top tank so I removed it for repair. After getting everything I thought I would need the following day,I was thinking I would be done in four or five hours. Well after cleaning up the mess in the engine bay and cleaning all the old paint of the...

I painted both my small blocks with long model brushes from the dollar store. They worked really good and i didn't get a bunch of over spray on everything like i always did. I did about three coats and it looked slightly dull,but once the engine was fired up and it warmed up to temp,the paint...

I am posting this information in this section to help any other members with mopar crate engines that have a problem getting them to idle due to a rich condition at idle. The cams that mopar performance use in their crate engines will carry a very low vacuum signal and can cause problems with a...

HOLLEY CARB TUNING TIPS Part 1: Carb CFM Sizing One of the first things to determine is what size...

If you run a 318 at the track ,what is your current setup and ET. Thanks ...8)

The shop i had do my cudas exhaust system is the best for the money i have ever seen. They did my coronets system years ago and that was really nice also. I gave them two mufflers,two collectors with gaskets and bolts,two hangers,two clamps and two flow master turn downs. They bent the pipes...

I am very happy with my 318 in my 67 cuda. I installed a 750 proform carb last week and just this morning installed a 3 inch thrush welded series muffler system. The car runs great and roast the tires in first at any speed. This ones for all you small block people. Let me know what you...

I painted my mufflers and all the hardware for the three inch system i am having installed. Thrush welded series mufflers in three inch will be replacing the 2 1/2 inch flowtec system. Here are some photos and videos of the hole process. I took a video of my car with open headers also. The...

I received my 750 proform carb and will be installing it on my 318. I just might have to do a good burn out and drive by. I also bought a proform fan(16 inch) I am a little sad to see my 750 double pumper leave because it's been with me for so long and won all my races with me. It went...

I went over to the garage to take my 750 double pumper carb off my 318 and got a little side tracked. ENJOY MY CHILDISH ACTIONS :thumbup: http://s1104.photobucket.com/albums/h337/t67power/?action=view&current=PICT1566.mp4...

I feel like a mad scientist.......................:glasses9: I am selling my 750 double pumper on my 318 cuda and will be installing a 850 proform carb. Why would i try such a foolish thing ........................ I am basing this on David Vizards testing done on a 383 chevy. He installed...

Anybody using these rockers???? Do you like them???? I was thinking of getting a set for one of my small blocks. It would be nice to use a set of 1.6 ratio rockers for cheap. It's the cheap part that I'm not so sure about. :burnout: Thanks for any info.

If you have any experience with proform carbs please let me know what you think of the performance and quality. Thanks.

Does anybody use proform carbs and if so what do you think of them????

Just wondering what the average rpm's are for your shift points. Please list the cubic inch , camshaft and cylinder head being used. THANKS :thumbup:

Who makes the cheapest new valves??

Let me know what your looking for and i will let you know if i have it. I have about ten for sale right now but might sell more. I have over 50 cars and if the price is right, i might unload more.