Search results for query: *

Does anyone have a pic of the inner fender splash shield that mound directly behind the front wheels of a 69 dodge dart. Trying to figure out what screws and washers that are needed. Thanks

I am putting dual exhaust on my 69 dart and the driver's side brake hose is getting in the way. I have got the tailpipe in but it's up against the brake hose and I mean tight. It is the 12-inch brake hose the goes onto the brass axle tee block that is in the way. Does anyone have a pic of there...

Hope you guys can help, put the door panels on for the 69 dart and the drivers door armrest will not attached with the screws ....does not have a threated insert. From what I can see, it is just a round hole and the screw goes right through. The door was from a 70 or 71. Can anyone chime in if...

What problems would i encounter switching from a 5.2 magnum to 5.6 magnum engine in a 96 dodge ram 1500. Do I need to swap wiring harness or ecu box. Any help would be appreciated

Bought a 22" restored rad from a member here that was suppose to be brand new. Still have a hang tag showing mopar number and size. I installed it and filled it with fluids and sat for 3 days and was ok. Got engine all hooked up and started it and ran for 20 minutes. Next day I noticed a 1"...

Final step in rewiring entire car .... can someone confirm this relay setup for a Choke. Please dont give me any other ways as I want to run a relay and want the choke dead in acc. and not heating up. Cannot do the oil pressure set up. Thanks guys

Has anyone used there new subframe connectors that bolt to the frame and the rear leaf mount.

Hey Guys ...after waiting 12 weeks for rims from local dealer ...going to order from summit but they do not have the 15x6 rims. i am going with the crager magnum 510. The rear will be 245-60-15 BFG on the crager 15x7 rims and the tires on front are 205-60-15. The car is a 69 Dart with the 11.75...

Where can I tap in the choke wire under the dash. I was thinking to splice it in the cig.lighter wire but can both work at the same time. Or would splicing into the radio wire .... was worried it may cause static in the radio or noise. Any other suggestions would be great as long as it connects...

Can anyone here decipher the codes on a 727. Would like to know what its from, this is what I found on case pk2801541j 2282 0648 2801261 DP 8 OD

Hey guys, got the 1.03 torsion bars in and was wondering if someone can chime in on the adjustments. The lower control arm adjusting bolt was loosen right off .... this is a complete resto so when i rebuilt the lower control arms ...I did not tighten the torsion bar socket in them. Now I turned...

Other then the bell housing ....is there a difference between the big and small block 727. Just want to no if any of the internals can be swapped between the two ... like valve bodies etc.

Need so help ....I had a custom Dash made by one of our members so now I'm taking the old gauge panel and inserting the new one with autometer gauges. The old wiring has two 5-pin connectors for dash gauges and turn lights. I think I can show it better below. Look at *** 1st - 5-pin Connector...

Do you guys see any problems using a 205/60/15 tire on a magnum 500 series crager and on a 15 x 7" rim or am I better off using a 15 x 6 rim. This will be on a 69 dart. It has 205/70/15 on it now on a 15 x 6 cop rim. The rears are going to be on a 15 x 7 magnum rims with a 245/60/15

Well...time to order tires and rims. Have gone through a ton of web sites and get conflicting remarks. If guys that have a 69 dart can chime in ...it would be great. It appears 70 and up darts have a little more room then the 69 and down darts. My question is will a crager magnum rim in 15x8...

Has anyone here used Driveshaft Specialist Inc. 8327 McCullough Avenue San Antonio Texas Looking to get a drive shaft made for my 69 dart ... 408 stroker with a 727 and 8.75. Engine makes 529 torque and 518 hp. so I want to find a good shop. I have the 1350 u-joints and yokes that I...

Back again .... Steering column has been all redone ... Went to put it in and the steering couple will only go over the first set of splines and cannot get it to go down far enough to put the roll pin back in. What am I doing wrong guys.

Hey guys, Just redoing my steering column and cannot remember what the bolts look like for the floor plate. There are 3 so I assume the should have large washers to cover the large holes in the floor plate and 2 smaller ones the the plate that secures it to the floor plate. Any pics with sizes...

Hey guys ..... Can someone check on a 69 dodge dart how the drivers side vent hose is located on the box. Does it go on the upper or lower opening on the heater box. Thanks Guys

Hey Guys, putting the 69 Dart back together and misplaced the rear upper shock bolts. Can any one tell me what size they are. The new shocks came with the large washers and inner brass insert but I need the rest. Not sure what ... I assume the go in from the trunk. Any help would be great.

Do not remember which wire goes on which terminal. If anyone has a pic of a 69 dodge dart showing a close up of the 2 wires for the washer motor ..... not sure which one is the terminal for the ground and nothing marked on the or by the terminals.

69 Dart, 360 fuel injected, auto. Hey guys, loosing it here, cannot figure this out. Late last fall, Car started and went for a ride. Got about 2 miles and it died as I was coming to a complete stop. Turns over but would not start. Fuel pressure was fine and checked coil power ....no power to...

Just refinished the heater box and picked up a kit from Detroit Muscle. I got a roll of grey caulking in a long strand. Where does this go and also when I put the two half's together, is there anything that seals them .... can't see it being the caulking ...any help is appreciated

Working on cleaning up the wiring in the engine bay. I wanted to run the alternator wiring direct to starter relay with a circuit breaker with reset, bypass the amp meter, clean up connections there and run wiring to some sort of fusable distributon block. i also have a small underdash amp that...

What gauge wire would you recommend for a powermaster 75 amp unit with external regulator. I seen 10 gauge on mads site but also was told you should run a 8 gauge. Also do you have any recommendations on a fuse holder and a part number that would work with it and should it be mounted just before...

Have a 360 .... do the motor mounts go on the inside of ears on both sides of the engine. Installing on a 69 dart .... have the original 318 on the passenger side and a 340 one for the drivers side. Looked at the other dart i have and it has both mounts on the inside of the ear. Also ...have...

Had a 408 stoker built and now putting all the hardware on it and found the square back mopar alternator has clearance issues with the iron indy heads. Has any member here run indy heads. Trying to keep it stock looking and not put the gm alternator in. Any suggestions

Does anyone have the torque specs for a 69 dart sway bar. Sway bar to k and end link torque in ft lbs. Thanks if you can help

Thought you guys might want to see this .... The hurst promatic shifter sells for about 270.00 on summit site and here is a link for the shifter for 99.00 us http://www.ebay.com/itm/271723748046?item=271723748046&viewitem=&sspagename=ADME:L:OU:CA:1120&vxp=mtr Hope this helps some members who...

Is there a easier way to drain a torque converter that is on a bench other then hooking it up and using the trans cooler lines to drain and fill with engine running. Would like to prefill while trans is out and change to synthetic. There is no drain plug on it.