Search results for query: *

To anyone, Is the company that bought out schumachers making the tri Y headers for big block A body?

I have a reverse manual in my 69 cuda with a 470 that is my daily driver. I would have it no other way. It's like being in the game pole position every day. Makes the drive to and from work actually fun.

Any experienced (A body Mopar big block experienced) Gear Vendors installers in MN. Recommendations.

I like what you did for added support, and I think I will add a welded-in psudo roll bar that reaches up to just under the package tray as a means to better stabilize the shoulder belts. Being a novice welder is definately my weaness in design, great job with the rear belts.

I didn’t get a chance to take a picture of my rear seatbelt set up. But I remembered now how I did it. I bolted the seatbelt retractors to the reinforced factory lap belt hold down the floor (this took a longer grade 8 fine bolt). The shoulder belt head went up and through the “slits” in the...

I think I got the retractors from one of the many seat belt suppliers that are online, so nothing special there. I think that on both far sides of the package tray there are factory "slits" for the seatbelts and I then cut a third "slit" for the middle belt. I'm going to my shed tomorrow and I...

I have a notch and I did 3 rear shoulder belts. I hope the picture comes through. The retractors are on the underside of the package tray which I reinforced with a large piece of thicker alum under each retractor. The shoulder belt is the stabilized under the factor seat belt buckle location...

I will look into all those things you guys mentioned. With the last rake pictured I don't even think he would need a pump, gravity fed to carb. You guys have been helpful, thank you.

I have an in tank aeromotive phatom 340 in Hot Rod Garage's A body tank which is fairly well baffled. My system is Fast Man EZ EFI. The rake of my car is flat protouring, not *** in the air. I was wondering that with my lack of rake angle that my pickup sock my not be in the lowest region of...

I know the title is long but it had to be. I have a Hot Rod City garage AL tank in my protouring 69 Cuda. I finally got it to that point of being a daily driver but I have been unable to get fuel gauge to work closer than being 1/4 tank off. That doesn't concern me as much as I'm not able to...

I believe I cleaned it out please try again

I don’t need the top bracket but the mech with that long arm is what I need. Cost and payment, are you ok with PayPal?

Could you post a picture. I want to be sure that it is 69’ because that is the only year that will work. Also include price

I need the hood release mechanism for 69 Cuda. I don’t need the support bracket.

One last time to all For A body Mopar members: can someone shoot a picture of your 67-69 Barracuda notchback rear belt line molding (of course while it is in place on your car). I would be even OK with a fastback picture.

I find no clip in the trim and the way the back part of the belt line molding looks it only looks like a small screw should be used. I think that possibly the guy I bought this from may have bondoed the hole over. Can you send a picture of the clip and holes related to your belt line molding...

I finally have gotten around to putting on the belt line stainless molding on my 69 Cuda Notch. I have no screw hole for the back part of 1/4 window belt molding to be held down and I can't find any pictures on-line to help me. Could some of you members take pictures of your 67-69 notch rear...

I will check them out. Thank you.

This is what I'm needing

I hate for the long header but I need to be descriptive. I need these clips These are the longer clips that click into the plastic grill surround (I think each side has 3-4) that have 2 flat projections that put pressure on the grill eggcrate to keep it to the plastic housing. I snapped 2...

Here is the question I have (I hope the pictures show), what should be filling in the open holes I have on the near bottom of my driver's side barracuda door 68'? Again, I'm near fully sure that have the 69' tracks and windows in this 68' door, am I missing some sort of track stabilizer...

Thanks to all you guys. My glass does fit well in the window track/mechanism and I know the glass was a 69', so 69' for both, and I know that I have a 68 door. Thanks for the exploded view of the 69' door mechanism. I still have 2 bolt holes in my 68 door that go to nothing, and I'm...

I know there have been past threads about this, but I need to see pictures that clearly show the differences (if any) at the end of a 68 vs. an 69 Barracuda door-drivers side please (not the hinge side). Reason, I feel when I got my car it had 68 doors put on a 69 body with 69 window...

I need 8, but 6 I guess would work, these are the S shaped clips. The B body clips that you can get new are too narrow.

Is it a complete car or just a roller?? More specifics please and then of course you cash price

Are you only interested in trade?? What about purchase? Need more specs on it please.

sounds great. I will be making payment today.

I take both the clip and screw for both sides. Send me a PM to set up payment and shipping

Perfect.

Send me a PM for payment and shipping requirements. By the way would you happen to have all the fasteners to put a 69' Cuda tail panel on. If so we could do a package deal.