Search results for query: *

  1. dusmon

    Strip Dominator and M1

    Has any one tested hp on a stroker between the strip dominator the 340 victor and the super victor. I heard the 340 victor was more hp than the strip dominator any one got some results on this ?
  2. dusmon

    Super Victor flow testing

    I have unported SV on my 416 best of 10.18
  3. dusmon

    Super Victor flow testing

    In the bottom hand written picture you show 3 intakes the 1st one you have ported edelbrock what manifold is that?
  4. dusmon

    Super Victor flow testing

    You 3 intakes what is the ported edelbrock?
  5. dusmon

    Roller LA cam into Magnum?

    Put new fuel pump in. that helped. Only thing not checked is the tune. As I don't have a way to do that. 25 year old ignition. No dodge dealer has the tools anymore. I did get the injectors phased and that was good. Get 17mpg, runs nice.
  6. dusmon

    Roller LA cam into Magnum?

    So what you say is a 360 like 1999 has a different cam that advertised by most on the net. I have a stock 1999 360 mag 4x4 that I think is a little doggie runs nice but not enough towing torque. I believe I have the .432 lift cam in that motor. do you have or know of some specs for my truck...
  7. dusmon

    Slap Stick

    I put a slapstick in my duster shifter out of a 78 Cordoba body style. So taller shifter rod. used 68 a-body z bar. Had to drill a hole in z bar to get proper ratio to work.
  8. dusmon

    [FOR SALE] 1970 Dart 1971 Demon NOS LH fender and Grill

    Do you have a picture of the inside of fender?
  9. dusmon

    Magnum camshaft bearing mystery

    I just rebiult a 5.9 magnum same thing #4 cam bearing was bad.
  10. dusmon

    Magnum 5.9 cam swap details

    How much lifter preload you setting them at?
  11. dusmon

    340 cam specs?

    same as in the 1980 direct conection manual just read it
  12. dusmon

    Trick Flow small block heads

    I had a set of comectics and after I pulled the heads there was pits from the gasket in the aluiminum head. and mine leaked so 1008 it has been for 10 years. I'm not a fan of Cometics.
  13. dusmon

    EDELBROCK PRO FLO 4

    I just bolted a efi pro4 on a 416/340 block edelbrock heads. Yes I had to grind on the intake to get bolts to fit in #3 and #6 inside intake holes and slot all bolts to heads as the ports lined up but holes were 1/6 high for bolts to fit. And cut 2 bolts shorter. And if edelbrock would raise...
  14. dusmon

    Show your 5x4 small bolt pattern wheels!

    What are a pair of 15x3.5 small bolt Centerlines Worth?
  15. dusmon

    Best guess on 416 motor

    plus 185lbs for driver
  16. dusmon

    Best guess on 416 motor

    10.18@130.19mph with that cam but its a ultradine.
  17. dusmon

    Best guess on 416 motor

    Just a update on this motor it ran a 10.18@130.19mph on Sunday the 13th of September I did a freshen up over the winter new rings, bearings, timing chain, new valve springs, put in heavier ones in and new smith brothers push rods. Fresh valve job as well.
  18. dusmon

    71 Duster 360 (new project)

    Why the missing frost plugs??
  19. dusmon

    Trick Flow small block heads

    pittsburghracer you are so right. I have been looking at this and any one that does good research on the trick flows will know that a lot of enginnering was done to fix old problems. But for the price and quality I think they are hard to beat.
  20. dusmon

    console shifter

    I am trying this very swap right now. So most of the day I was getting a slap stick to work in my 1974 360 duster factory console car. Here are my findings. E-body z-bar to short to work from a Cuda. But measured the distance on holes so I could use those findings on a 1968-9 a-body z-bar...
  21. dusmon

    console shifter

    How far in did you drill the hole?
  22. dusmon

    71 Dart get 408/ Trick Flow Heads....

    I had to grind on that super victor to make room for bolts and distributor to fit. So test fit it as well as the valve covers. Had to clearance them as well.
  23. dusmon

    71 Dart get 408/ Trick Flow Heads....

    I have one on my 416 with Indy TA heads and the port job, 950 QF carb . 10.29 et in my Duster 5000 stall in a 998 with low gear 4.56 dana 31x13 MT tire.
  24. dusmon

    71 Dart get 408/ Trick Flow Heads....

    How much are the push rods? From SmithBros
  25. dusmon

    Trick Flow small block heads

    Well keep us posted very interested in the build.
  26. dusmon

    Trick Flow Intake

    Wow never seen one like that. looks like a ice box to keep cool intake charge.
  27. dusmon

    Trick Flow small block heads

    if you read my build you will get there you will have better heads.
  28. dusmon

    Trick Flow small block heads

    Did you buy the trick flows?
  29. dusmon

    Trick Flow small block heads

    Just so you know Indy will rip you off with their junk. I have 2 sets of Indy T/A heads. And will never buy Indy again. No customer service at all. If I buy a 3rd set It will be Trick Flows.
  30. dusmon

    1970 Duster head rests Wanted

    I'm looking for a set of dark green head rests for a 1970 Duster with bench seat. Where can I buy new or even used in mint shape. Thanks Guys
Back
Top