Search results for query: *

Just noticed today that my fresh air box door when I opened it in the driveway was full of water?? The carpet on the floor was drenched. I think the stupid sponge rubber donut I bought which seals it around the lower cowel pan is leaking. I ran some water in the outside cowl louvers and sure...

Does anyone here know the size and type of screw that goes into the rear of the housing and into the plastic lens of my Demon. I seem to have forgot them. My rear lights are leaking water into the trunk. There are 6 of them on each light and I do not want to use the wrong size and break the...

This is a 6pcs set I had in my 72 Demon. I bought these brand new and have since opted for something with GPS so this is for sale. These are almost new. The speedo was never hooked to the tranny and I have the adapter that goes on the tranny. All other gauges were operating fine. The fuel...

I have a 416 stroker 340. I have a griffin radiator with custom built griffin shroud and twin electric fans. Edelbrock heads and doug headers. They other day I drove a bit. It was about 93 degrees. My autometer temp guage crept up to 210 and I was getting a little nervous. I have a 160...

Just used my power probe. With the ignition key on and the NOS 2 speed wiper switch off, all terminals at the motor plug are dead. With the switch in low I get 11.4 volts at the terminal which plugs on the lower spade. With the switch in high, I get 11.4 volts at the terminal that plugs to the...

Currently running a holley avenger 770. Holley website says I should be running an 870 cfm carb on a mild 416 stroker motor. My issue is that at idle my car seems to be running real rich when I smell the eye burning exhaust. Once I am underway it seems to clean itself up. I was thinking that...

My 416 stroker has been done and driven now for about 2 years to cruise nights and shows. Today, about 70 degrees now, I took her out for a cruise. She usually runs at about 190 degrees. Sometimes creeps up to 200. But today it starter to go over the 200 up to about 210-215? Very strange...

I need the passenger side roof trim that holds the headliner up. I just need the straight over the windows piece. I have the back and front pieces. Also it need to have the clips that snap it in place. It is basically almost straight and about 3 feet long. Can slide into a small shipping tube.

Looking for a nice pair if the plastic door emblems for my 72 Demon.

Why can't I get the chrome interior threaded escution to tighten. The mirror has a tin nut which gets threaded on first. Then the cable end gets inserted in the door hole from within and the chrome nut threads on to the mirror adjuster knob but it hits the tin nut and won't pull tight to the...

Just installed two years ago. Started my car today for the Spring and my Royal Purple was dripping all over the ground. I thought it was just the tranny fitting that needed to be tightened. Put her up on the lift and started it up. Line was pouring fluid about 6 inches away from the tranny...

As stated in the heading. I have a front split bench seat with the center armrest in my 72 Demon. The passenger side seems to jerk front to back while I am driving, starting, stopping? I tried it in various settings and nothing seems to help? Any ideas what would cause this??

Nice mirror for the drivers side of a 72 demon. fits many others as well. looking to get 25.00 for it. plus the ride.....

this is an 18" fan with a new clutch drive for an abody car. I would like to get 75.00 for it. The clutch is brand new and the fan is original. Both parts in excellent condition.

Hi, I am looking for the drivers side mirror remote cable bracket and screw. This is to hold the cable so it won't hang up the window. It gets mounted to the upper front leading edge of the door under the rubber top gasket. Anybody have on??? Thanks

Hi, I have an electric fan with shroud. They are both brand new. Never used them. They are for a 22" radiator opening. I did cut a little off the edge of the shroud but never used it. I also just found the Northern High Performance Z40078 fan relay wiring brand new in the package. The...

Fan has never been installed. Aluminum shroud has a little trimming done to edges. I would like to sell this as a complete unit for 70.00 plus shipping. No relay. Fan is a model FLX-216 and cost 80.00. Aluminum shroud is a fit for a 22" radiator and cost me 110.00 at Carlisle. Bought both parts...

Hi, I have a nice 18" fan with a brand new clutch that has the short stem for clearance. It is in excellent condition and I no longer need it. I am going to Carlisle and will sell it for $100.00 complete. Let me know.

Hi, I have a duster trunk lid. I am going to Carlisle and will bring it with me if anyone wants it? It is in decent shape and I will sell it for $75.00 delivered to Carlisle. I did not spend a lot of time and only have the one picture. Backside is ok and may need a little work on the seam...

Hi, I am going to Carlisle and I have a Pair of Dodge Demon fenders I do not need. They are in pretty decent shape and I will bring them with me if somebody needs them. I am showing both fenders. One is the front side and the other is the back side. Did not take a lot of time for photos. I...

Fan has never been installed. Aluminum shroud has a little trimming done to edges. I would like to sell this as a complete unit for 70.00 plus shipping. No relay. Fan is a model FLX-216 and cost 80.00. Aluminum shroud is a fit for a 22" radiator and cost me 110.00 at Carlisle. Bought both...

This is a nice 18" 7 blade fan with the clutch. Clutch is brand new and is for the closer fit shaft on it. Fan is an original pentastar fan from a 70-74 abody. I would like to sell the both parts as a unit for $100.00 firm, plus shipping. IT IS AN 18" FAN and NOT A 16" AS TITLE STATES The...

I have a slightly used 22" aluminum radiator for an Abody car. It is in great shape and I have no use for it. I believe I paid 369.00 for it and would like to sell it for $125.00 plus a little for shipping to you. The fins were touched when I was installing the fan and clutch so that little...

Having a hard time installing my lower radiator hose. As picture shows, I pushed the upper end onto the water pump neck and am finding the lower end to be sitting way to low to pop on the radiator tube? In order to raise the lower end up, I would have to cut the upper end by about 3" which...

Hi Guys, I installed what griffin calls a direct fit aluminum radiator with the custom built aluminum shroud and 2 spal 10" fans. Came with 2 relays. So, I wired the two fans placing the ground wires for each fan in a different location. I then wired the fan supply to the red feeds from each...

looking to install in my demon bench seat car? what is the best type, size and mounting location? Pictures? Thanks...

All the ads say 71-72 demon. But I understand that there is an actual difference between the two years regarding the rear tailpanel stripes and emblem. Does anyone here have a picture or an explanation of what the difference is and what is the correct for 72 340 demon?

This a a brand new pair 0f deluxe front door panels for a 72 dart or demon. I would like to get $150.00 for the pair. Never been installed.

Wow, I think the hardest part about doing my demon was getting brackets and pulleys to work with each other. Point at hand. My 340 was built with edelbrock aluminum heads. Problem is, nobody told me that these aluminum heads protruded out in front of the face of the bloc by about 1"? Enter...

Question is if I install a shroud on my US Radiator and put a 16" spal fan, does the fan have to be offset, of can I just put it in the center of the aluminum shroud, which would be offset from the engine by about 2"? Would I be better off with the one 16" fan or I understand I can fit 2 10"...