Search results for query: *

Car was originally a 340 S car now has 440. Mainly used as a drag car but can be put on street pretty easily. Motor has steel heads and hyd. cam, electric fan and water pump. Motor was rebuilt not long ago nice fresh rebuild. 727 trans reverse manual valve body 10in Dynamic converter. 8 3/4 rear...

For Sale Fiberglass Hood with Hemi scoop used in good condition has some cracks by scoop and scuffs on corners of hood.Fits 67 68 Barracuda. 75$ Fiberglass decklid fits 67 68 69 Barracuda (trim is drilled for 68 .Good condition has some minor scratches on it. 75$ obo Really do not want to...

I got all the parts ...Thanks!

I'm in need of hood hinges and springs..or (lightwieght springs) also need all locking hardware for deck lid and catch that attaches to body. Thanks

I have a 68 Barracuda with manual steering. The pitman arm has alot of play in it where it fits into draglink. Also the end does not fit tight into drag link to it seems to bottom out before it tightens.....the draglink doesnt look oblonged. Maybe parts are wrong or drag link is wore out...

Yes they do......ill try to find photo...motor is in another garage.

The ADJ. rockers dont ride right on tip.....can you shim rockers? Some of are riding to the right and left.

Im looking for Mopar Performance Rockers,Shafts and pushrods for my 440. I have adjustable rockers now, i am going to hyd.cam so i want to switch rockers. Thanks

I have a pin on deck lid..i would like a steel one in any condition...send me pictures...local chicagoland pickup would be great!!!

ill give it a try thanks!!

http://prestoliteperformance.com/Portals/0/downloads/mallory/pdf/Mallory_Instructions_hyfire_6_series_685_6851.pdf here is link..it is figure 15

i am using unilite, powermaster coil,& digital 6 box.Mallory shows to use ballast but it doesnt show where to wire voltage regulator to. now i have it wired like this, one side of ballast i have brown wire(from bulkhead "Q"), red wire going to box,& red to dist. other side of ballast i have blue...

I belive 68...not 100 0/0.

I have 2 heater boxes out of Barracudas one is a a/c box with controls and wiring harness, it has a piece that cracked off, it can be repaired. The non ac box is just the box. 100 for ac, 50 for non....plus shipping..or make offer

NOS 170 slant six with three speed overdrive,bellhousing,flywheel, my father bought the 6cyl in a crate years ago.make offer. also have 18" clutch fan it is almost brand new. 75 plus shipping. new mopar performance oil filter 10 plus shipping.

I need new axle bearings...where can i find some?

Is it pretty easy to swap....do you have to reset gears or do they stay in case?

ok....thanks for the info

I had this center section sitting for about 15 years i pulled it out to use it and i think it is a open rearend...? it is a 489 case with 411 gears ... who would put 411 gears in a open rearend? The other picture is the 741 case out of the car it has 3.23 gears in it. Can the posi unit be...

Does anyone have a picture of lower trim or have any for sale?Here are holes on my cuda, i havent seen trim for it anywhere

OK, that's what I thought I wanted a second opinion before I go buy one.

Is there a special transmission for A body (big block) or are they all the same? I don't know if A body has a differect length transmission or are they all the same (B Body, E Body)?

I have a 741 case in car with 3.23 gears....i found a 742 case with 4.11 gears i want to put in my car but the yokes are not the same, the one in the car is about 3 3/4 in width the one on 742 case is about 3 1/4. My question is can i just swap them is there a cruch bearing or something i will...

OK thanks Blownfish....Woodgrain it is !

Very nice Fish you caught!

is the build date on the fender tag?

yes factory tach......it is not very accurate though.....the car has alot of options power disc brakes. power steering...light package...rear defoger..am fm radio & some bottom trim that i cant find anywhere the holes are in the body still.

Wondering what is the correct shifter knob for my 69 Barracuda. Is it the one in the picture or is it the wood grain??

Here's pictures of my car. Weather was crappy so, the car stayed in the garage. Getting car ready for 1st race in 1 month!

New member & new to forums....Got the car from my father it ran a couple of times about 5 years ago other then that has been sittin for about 15 years! i have been working on it for about 2 weeks now got it running pretty good!ill have pictures in a couple of days. i am thinking of taking it to...