Search results for query: *

I'm in the middle of rebuilding my brakes, new lines, calipers, rear wheel cylinders and master cylinder. The master cylinder seals went and blew debris into the valve on the frame. I have the rebuild kit, but it must cover a few valve blocks. Mine is stamped 347-B, does anyone have a diagram of...

I was sitting at the bar staring at my drink when a large, trouble-making biker steps up next to me, grabs my drink and gulps it down in one swig. "Well, whatcha' gonna do about it?" he says, menacingly, as I burst into tears. "Come on, man," the biker says, "I didn't think you'd cry. I can't...

I'm looking for a fuse block for a 1967 Barracuda, part is marked 2497964

I need to rebuild my AFB, it's been done once and the accelerator pump only puts out a weak stream. Who makes a good rebuild kit??

Father Norton woke up Sunday morning and realizing it was an exceptionally beautiful and sunny early spring day, decided he just had to play golf. So... he told the Associate Pastor that he was feeling sick and persuaded...

I guess you can't post photos in the conversation section. Can this manifold be opened to 2 1/4 " without creating any problems??

I hope this is wrong!

I rebuilt a 90 360, new rods, KB107 pistons and old crank. The crank journals showed no wear. It has fine oil pressure, runs great and will idle for hours and not overheat. It has about 200 miles on it plus more then a few hours idling. The heads are new magnums, the block was well cleaned at...

Subject: When Men get to be over 70 I was standing at the bar one night minding my own business. This fat ugly chick came up behind me, grabbed my behind and said, "You're kind’a cute. You gotta phone number?" I said, "Yeah, you gotta pen?" She said, "Yeah, I got a pen". I said, "You better...

I got a call yesterday from a friend asking about the early B body 4 speeds. He has a cast iron short shaft t-10, we think it's from a 62-63 B body. Is there any way to verify what it is? Does anyone know what the value is?

I'm looking for a plug number for a mild 10:1 360 with magnum heads. What do you guys recommend?

I'm looking for a set of cupped washers and exhaust bolts. The washers are a must, I can make up the bolts if I need to. The manifolds are 1974 340/360 if that makes any difference.

It's finally in the car, I'm beat! Now on to the aux stuff. It took a long time getting this far.

I have 2 questions, can anyone tell me the size of the allen wrench I need to adjust the advance in the vacuum canister. The second, I'm looking for the best timing tape to use on my harmonic balancer and what cement/glue is best to use? I've heard about using clearcoat to fix it. Thanks for the...

We have snow on the ground here, here we go again!

Can anyone tell me the length of the pedal to zbar, center to center. How much of an offset is there at the zbar? Thanks, Bob

I was digging through my parts and came across this, The part # stamped on it is 512805. Does anyone know what body/trans it fits?

I'm looking for the small 1967 P/S output shaft nut and washer for my new P/S box. Anybody have a spare?

I'm looking for the mate to this trans harness. I'd like to get the female plug with ends if possible. It's for a 727 3 pin back-up/Neutral safety switch.

I'm getting ready to ship my PS box out to be rebuilt, I'd like to get some feed back on what level to go with. This is for a 67 Barracuda convertible with some work on the suspension. I'm using Steer & Gear and thinking about level 2 or 3, probably 3. Will that be too stiff?

What effect does a larger bore caliper have on front disk brakes? Also, has anyone used the yellow EBC pads on their cars and how much improvement did you see?

I bet that got your attention! I'm rebuilding a set of lower control arms and not sure if the pins are set deep enough. Here are some pictures, what do you think? They are bottomed out on the bushings, I'm not sure they're not deep enough.

Picture of the Delaware Watergap, I'll be glad when this winters over

So I'm coming home from bowling late last week and a funny thing happened, I got stuck behind some moron doing half the speed limit. I didn't get the license plate but watch out for them. Here's a few pics..

It's snowing here and starting to turn everything white. I just want to wish all a Merry Christmas and a Happy New Year!

Has anyone used one of these?

You have to see this video, one amazing car guy!! http://www.youtube.com/embed/qiLDMBDPCEY?rel=0

I just want to thank 71Dartboy, he's a great guy to deal with. I bought his magnum intake, it is one beautiful piece. Thanks again...Bob

Does anybody know the size of the intake bolts on a small block magnum M1 intake??