Search results for query: *

  1. Nkempski

    Tranny lines

    I recently put in a B&M floor shifter, and used the stock tranny lines. They were not damaged, so I didn't change anything. I did order a new set of tranny lines to replace the old ones because I was under the car anyway, but they didn't match up the right way. I'd only replace them if...
  2. Nkempski

    Camber adjustment/rack and pinion

    There's a weld on the shock tower that is where the camber bolt turns. I can get it to turn when the wheels are on the ground, but not when it is up. Upon further research, the problem might be a bad bushings in the lower control arms. I'm going to replace both of those first. I'm have uneven...
  3. Nkempski

    Camber adjustment/rack and pinion

    Hi Everyone, I have a really bad weld on one of the shock towers where the camber adjusts. I cannot get the alignment right. I have a 1973 Dodge Dart Swinger. It looks like the car may have had some structural damage at some point in its lifetime. Anyway, my question is, if I install a new...
  4. Nkempski

    Best stock oil pan for400 stroker to500 BB in a 70 Dart ??

    I just did a 400 swap in a 1973 Swinger, and I had the best luck with the Milodon Low Profile Center pan. I still have a small issue with the drag link grazing the pan on the passenger side, but it isn't severe. It can be fixed by either lowering the drag link or readjusting the motor...
  5. Nkempski

    ... a resto-mod project - finally on the road ...

    Looks great! Congrats on getting it out on the road!
  6. Nkempski

    Bench seat reupholstery

    I did the rear bench seat in a 1973 Dart. It was a legendary cover. I bought the hog rings and tool. I did it in my family room. I had no issues stretching the material, but if I didn't have the tool it would have been hard. I didn't have to use heat, but I could see using heat without the...
  7. 1973 Dodge Dart Custom Big Block

    1973 Dodge Dart Custom Big Block

    Bought this car in 2011. I am the 3rd owner. The previous owner said it was a 1972.5 Dodge Dart because of the front clip. No idea if that is true, or if someone installed the 1972 front clip. Built it to be a street rod. Need to install new inner fenders. I cut the inner fenders out when...
  8. Nkempski

    Mancini Disc Brakes

    I haven't used Mancini for the disc brakes, but they have always been great to work with. The parts have always come quick, and fit the way they are supposed to. They also have been very helpful on the phone. Sorry I can't comment on the disc brakes, but I'd have not qualms at all about...
  9. Nkempski

    Lowering Center link (drag link)?

    Thanks guys. I am using a motor plate and the mounts are all welded in. I need to see what shimming the plate will do to the header clearance in other areas. Thought I had this issue handled, but after driving it a bit, the center link is still rubbing. I switched to a 72 center link set up...
  10. Nkempski

    Lowering Center link (drag link)?

    Thank you. I can't find that online. I can find the chasis manual, which I think will cover it, but can't find it readily available.
  11. Nkempski

    Lowering Center link (drag link)?

    I have a 1973 Swinger with a 400 and pro parts headers. A center sump Milodon oil pan. I am having some minor clearance issues with the center link and driver side tie rod end. If I dropped the center link by a half inch, I'd be fine. I switched the center link, pitman, and idler arm to the...
  12. Nkempski

    Pro Parts Exhaust

    I am finishing up a 1973 Dodge Dart with a 400 Big Block. I have the Pro Parts full length step headers for the A-body Big Block. Anyone have an exhaust system they recommend that worked with these headers? I'm leaning towards just taking it to a place, but thought I'd ask for input here first.
  13. Nkempski

    Wiring help

    Thank you greatly! I really appreciate you walking me through it. I was good on electric until I got inside the car. This helps tremendously.
  14. Nkempski

    Wiring help

    1973 Dart
  15. Nkempski

    Wiring help

    1973 Dart. I’m horrible with wiring diagrams. I can’t figure out what it is from the diagram.
  16. Nkempski

    Wiring help

    It’s a 1973 Dart
  17. Nkempski

    Wiring help

    Thank you!
  18. Nkempski

    Wiring help

    That’s what I thought too but it has 3 connections. My flashers have 2. Is there one I’m missing?
  19. Nkempski

    Wiring help

    Anybody know what this connects to? 2 yellows and 2 pink. The pink are hot. It’s located under the dash between the radio and instrument panel.
  20. Nkempski

    [SOLD] Fenderwell Headers BB A Body

    Used big block A Body Hooker fenderwell headers. A bit dinged up. Biggest spot is on the collector in the picture. Aurora, IL. $100
  21. Nkempski

    [FOR SALE] 1973 A Body Manual Steering linkage

    1973 A Body manual steering linkage. Includes drag link, pitman arm, and idler arm. Pitman is for a manual steering box. $75
  22. Nkempski

    [SOLD] 906 Heads

    Stock 906 heads with valve job. Stock springs. Ready to go. Rocker arm assembly included. Casting: 2843906 $150. Aurora, Il. Pickup only.
  23. Nkempski

    [SOLD] 440 block

    No strip bolts. No cracks. No broken ears. There’s one cylinder with a scratch in it. Not enough for a finger nail to catch. I was going to rebuild but I’m moving and need to unload stuff.
  24. Nkempski

    [SOLD] 440 block

    It’s just a stock bore. I don’t have anything to measure it with or I would.
  25. Nkempski

    [SOLD] 440 block

    440 block 1977. Looks clean. No real issues with cylinder walls. Pickup only. $300. Aurora, IL.
  26. Nkempski

    [SOLD] Free 904 small block trans

    Thanks guys. If it’s a 904, it’s free. Pickup only. Can’t figure out how to edit the post. Aurora, IL.
  27. Nkempski

    [FOR SALE] New MSD Blaster SS

    New MSD Blaster SS ignition coil. $40.
  28. Nkempski

    [SOLD] Free 904 small block trans

    I was told 727, but could be 904. If anyone is interested I’ll give it a closer look.
Back
Top