Search results for query: *

  1. R

    Wheels

    Thanks!
  2. R

    Wheels

    Nice, if you do pick it back up please post tire sizes. Thanks
  3. R

    Swapping bench to buckets

    Cool, thanks!
  4. R

    Swapping bench to buckets

    Thanks for the warning :thumbsup:
  5. R

    Swapping bench to buckets

    Thanks!
  6. R

    Swapping bench to buckets

    Thanks guys. Are '67-69 A body the only tracks that will work? I see the floor reinforcements fit through '76 - are the pans the same?
  7. R

    Swapping bench to buckets

    Besides seats and tracks is anything else needed to swap from a bench seat to factory buckets on a '68 Barracuda?
  8. R

    Wheels

    That looks great What size tires and wheels?
  9. R

    63 Wagon tires

    I’d go with at least a 165/80x13 to get a bit more height to fill the wheelwells
  10. R

    Factory Floor Shifter Linkage

    Getting a '74 Dart sport running after it’s been sitting for a long time. It’s a console shift car but some of the linkage is missing. What exactly do I need to connect the shifter to the trans? I'm guessing there should be a bracket that attaches to the trans and a link going forward to the...
  11. R

    [WANTED] 1973-76 Dart Hood Wanted

    Wanted - hood for 1974 Dodge Dart. Prefer SoCal area if possible. PM or text/call 714 482 7175 1973 1974 1975 1976
  12. R

    440 Oil Pump Won't Prime

    Thanks, yeah it’s definitely obvious who actually read the original post!
  13. R

    440 Oil Pump Won't Prime

    Thanks for all the responses - I found the problem - the gasket between the pump and block was incorrect and blocked off one of the oil passageways. I’ve got 55psi with the drill so it’s good to go.
  14. R

    440 Oil Pump Won't Prime

    I’ve run the drill for at least 2 minutes multiple times, surely that’s enough?
  15. R

    440 Oil Pump Won't Prime

    25w/50 and between 55-75 degrees depending on the time of day I’ve been working on it
  16. R

    440 Oil Pump Won't Prime

    Yeah, turning the pump counterclockwise
  17. R

    440 Oil Pump Won't Prime

    It’s a new pickup. Drill doesn’t bog at all.
  18. R

    440 Oil Pump Won't Prime

    Already done that - I swapped to a different known good pump that just had a coating of engine oil put on the rotors and housing.
  19. R

    440 Oil Pump Won't Prime

    This driving me nuts! Swapping in a 440 motor home motor. Had to change the pan and pick up to car style ones, used a factory pan and factory style pickup which is right on the floor of the pan. Put new gaskets/seals in the pump while I was at it. I packed the pump with petroleum jelly to help...
  20. R

    'Stuck' A833

    I’ve pulled the side cover off, didn’t notice anything out of place although there is some surface corrosion from where moisture has got in. The countershaft rocks back and forth with the input shaft. I guess I just need to tear it down.
  21. R

    'Stuck' A833

    I've got an A833 that's been sitting for a while and I can't rotate the input shaft more than a couple of degrees in each direction. It feels like a transmission that is in two gears at a time but it is in neutral and the output shaft turns freely. Any suggestions for the likely cause before I...
  22. R

    [FOR SALE] Nice Set of 4 1968 Plymouth Wheel Trims

    Great condition set of full wheel covers for 1968 Plymouth 14” wheels. No scrapes or dents, $50 obo plus shipping or pick up in Fullerton California.
  23. R

    Floorpan Interchangeability

    Looking at a '68 Barracuda that had the rear floors cut out for a tub job that was never finished. Would the floorpans/inner fenders/trunk floor from a Dart or Valiant be the same so I could put it back to stock?
  24. R

    [WANTED] Caliper Mounts for 11" Rotors/Pin Mount Calipers

    Finally got the adaptors from my buddy so ready to trade. PM sent to 66fs
  25. R

    [WANTED] Caliper Mounts for 11" Rotors/Pin Mount Calipers

    Haven't been able to get the large pin ones from my buddy yet. Will hopefully get them later this week. 66fs is first in line to trade but if tat doesn't work out, I'll hit you up.
  26. R

    [WANTED] Caliper Mounts for 11" Rotors/Pin Mount Calipers

    Looks good. My friend still has the other brackets and is out of town until the weekend. I'll get some pics once he's back. Thanks
  27. R

    [WANTED] Caliper Mounts for 11" Rotors/Pin Mount Calipers

    Sounds good, let me know when you're back and hopefully we can work something out
Back
Top