Search results for query: *

Besides seats and tracks is anything else needed to swap from a bench seat to factory buckets on a '68 Barracuda?

Getting a '74 Dart sport running after it’s been sitting for a long time. It’s a console shift car but some of the linkage is missing. What exactly do I need to connect the shifter to the trans? I'm guessing there should be a bracket that attaches to the trans and a link going forward to the...

Wanted - hood for 1974 Dodge Dart. Prefer SoCal area if possible. PM or text/call 714 482 7175 1973 1974 1975 1976

This driving me nuts! Swapping in a 440 motor home motor. Had to change the pan and pick up to car style ones, used a factory pan and factory style pickup which is right on the floor of the pan. Put new gaskets/seals in the pump while I was at it. I packed the pump with petroleum jelly to help...

I've got an A833 that's been sitting for a while and I can't rotate the input shaft more than a couple of degrees in each direction. It feels like a transmission that is in two gears at a time but it is in neutral and the output shaft turns freely. Any suggestions for the likely cause before I...

Great condition set of full wheel covers for 1968 Plymouth 14” wheels. No scrapes or dents, $50 obo plus shipping or pick up in Fullerton California.

Looking at a '68 Barracuda that had the rear floors cut out for a tub job that was never finished. Would the floorpans/inner fenders/trunk floor from a Dart or Valiant be the same so I could put it back to stock?

Anybody got a spare pair? Could trade for pin style caliper mounts for 11.75" rotors or buy outright. Thanks

Complete set of 4 doors from 1965 Dart 270. Have glass, regulators etc. Rust free and pretty straight. Free to collect. Located in Fullerton California.

Low mileage 360 shortblock 0.030" over, Magnum heads drilled for early intake with Mopar Performance valve springs and conversion pushrods, performance cam, double roller timing chain, SFI legal damper, Edelbrock intake, electronic ignition, Carter performance fuel pump, Milodon oil pan, gaskets...

1963 Dodge Dart station wagon, 360ci with Edelbrock intake, 4 speed trans with hurst shifter. Disc brakes, Firm Feel heavy duty torsion bars, 8.75" rear end with 3.23 gears. Vintage 5 spoke mags with good tires. Solid So Cal car, original paint. Clean uncut dash, tidy interior. Power rear...

The driver's door lock on my '63 won't turn with the key anymore. Can they be stripped down and rebuilt? I'd rather not replace the lock as I'd like to keep the same key as for the passenger door and tailgate.

I've got a coil off a 5.2l Magnum that I want to use with an HEI module but I need to know which wire is positive and which is negative. I've attached a picture of the coil and connector. Thanks

My '63 Dart will crank over fine but not start until you release the key from the start position. I'm currently running a 360 with a points distributor but also had the same problem when I used to have an electronic set up on it. I've replaced the ignition switch with a known good one and...

My '63 Dart has been parked up for about 4 years and now the temperature and fuel gauges don't work. They worked when it was parked and the wiring wasn't messed with whilst it was off the road. What's the most likely fix? The oil pressure light and turn signal indicators in the dash flash so it...

Garage clear out - small block stuff, all parts $5 each Electronic distributors 318 oil pan (center sump) 360 oil pans (rear sump) Timing cover Stock rockers and shafts 318 harmonic balancer 360 harmonic balancer Various camshafts Probably have some other stuff lying around too...

360 shortblock +0.030" $100obo Early 318 LA shortblocks, thick wall casting, forged crank, std bore $100 obo Prices do not include shipping. Local pickup preferred - Orange County So Cal

Wanted pair of 14x6 slot mags or 5 spokes

Holley Street Dominator intake manifold with injector bungs, factory Magnum injectors and fuel rail. $100 obo plus shipping

Any preference between Brewers and Passon as sources for a rebuild kit? Thanks

Anybody have an exploded diagram of a '63 Dart steering column? Thanks

How different are the floorpans on the early As compared to the later ones? I was thinking of using this exhaust system http://www.summitracing.com/parts/sum-680144/overview/make/dodge/model/dart and modifying to fit. I already have tailpipes on the car so I'd either just use the section...

Running 318 - think it's originally from an early 70's Dart. Complete carb to pan. No flywheel, starter or exhaust manifolds but has water pump, alternator and pulleys. Thermoquad carb, electronic ignition and Weiand dual plane intake. Was running fine in my '63 Dart until the trans locked up...

I have a 4 speed out of a '74 Dart sport with stock bellhousing and a 130T flywheel for a 360. Am I right in thinking that if I get the complete clutch I can use either a 10.5" or 10.95" clutch with no problems? Thinking of getting this McLeod StreetPro...

What's the maximum lift a stock 308 head can take before running into retainer clearance or coil bind? I want to put some stock heads on my 360 as a temporary measure to break the cam in and give me some time to port/rebuild a good set of heads.

I've diagnosed a bad ballast resistor on my Dart, but not sure what ballast resistor I should ask for at the parts store - it's a '63 Dart with a 318, electronic ignition with 4 pin ECU and single ballast resistor. Not sure what year/model vehicle the ignition came out of. Thanks

I picked up some miscellaneous spare parts which included a bunch of coils. Is there any way to tell if they are for a points or electronic ignition?

Slightly o/t but hopefully someone can help. A friend is looking for a power steer box for his Challenger. I seem to recall Mopar p/s boxes are pretty much interchangeable all the way from the early '60s into the '80s except for differences in output shaft and possibly input shaft? My...

I have 2 383 motors - a '66 out of a Satellite and a cast crank '71 original application unknown. I want to use one motor in my Ramcharger and the other in my Dart. I'm planning on using the '66 short block for the Dart but was wondering which heads have better performance potential. The...

Does anyone have any suggestions for a starting point for jets/rods in the TQ for my Dart? It's a 318 out of a '71 Dart, stock internally with a Weiand dual plane intake, no EGR or air pump, recurved electronic distributor and Magnum manifolds with dual exhaust. I've looked at the Vaanth TQ...