Search results for query: *

Maybe anyone can answer, but my question is I have a 73 Plymouth duster with a bench seat factory 4 speed. I've spent a lot of time trying to locate the factory shifter handle which I have. I was just wondering it seems like the shifter handle is close to the Steering wheel or the driver side...

I'm in the process Of redoing the 340 on the quarter panel on my duster Remove the vinyl numbers which was easy , but there is A ridge around the parameter of Where the numbers used to be.I can't get rid of it. Tried three m Adhesive. remover... I tried goofoff adhesive remover, Also tried...

The reason I am bringing this up is I am second-guessing now after rereading a lot of posts on four speed duster bench seats. Finding that they say a 7036 is the right one... anyone help thanks....

I have a hurst 4 speed shifter handle and knob that came off of my 73 duster.it is the two bolt in style.. has the #4105 on the handle. 100.00 plus shipping.

I need to identify this hurst handle 4105

I have checked the front end parts Ball joints Tierod ends ect..nothing seems bad, only thing I found was the lower shock mounting rubber is bad...going to replace them and see what happens

I'm having an exhaust system.Put on my 73 duster and I have factory exhaust tips.My question is, do they get welded?Or. Not

What holds the plastic splash panels on? Under the front fenders thanks I need to know what hardware to buy thanks

My 340 has no timing tab on either side on the timing cover...

When I bought the car, the guy stated that the front brakes were locking up. But I didn't think that would be a big deal. Or a deal breaker when I purchase the car. When you drive the car, if you push on the brakes slowly it will stop if you use the brakes. Normally the front will lock up , but...

I am looking to have a dana 60 cut down That someone had given me to put in my duster...my ? Is do I make it to fit the one that is in there now or make it a shorter in length to help with tire selection

While messing with the sending unit on my duster, I noticed that the vent line at the top of the gas tank was not hooked up. There was a short rubber hose than a going up to the is. No canister. what's my best option? I have did a search but it is all over the place thanks

Is there a replacement tire for the mickey thompson indy profile n50 14" tires

Looking for a factory 340 4 speed hurst shifter handle thanks..

My question is, what is the shifter handle supposed to look like with a bench seat? This is what mine had in it when I bought it. Not sure if it's the right one or not seems to work okay.

Looking for a mopar tuff wheel and adapter for a plymouth duster thanks

I noticed that the clutch rod for the throwout bearing arm. Has an adjusting nut that it looks to be a castle nut. My question is, which way does the nut go I would think the flat end would go against the rubber piece but other pictures that I've seen shows at the other way around.

I'm looking for the Fender brace that goes at the bottom of the Fender over to the bracket. Or frame that keeps the lower Fender from bounce and around. I think the right and left side are both the same thanks

Looking for a factory 1973 duster radiator Inusable condition. Thanks

So I picked up a duster today with a 340 4 speed my question is, it's been a while since I have driven a 4 speed but I noticed that to clutch is super heavy and comes up pretty far off the floor before it will release, everything seems to shift. Good but it seems like the pedal sits high that...

Does anyone know what trim ring fits this will I believe it's a 14 inch deep dish rally. Thanks

I am looking for a adapter for the steering wheel to put an aftermarket tough wheel on my 75 Duster thanks

I have a 75 duster that came with a wing that was installed...it's not in the proper location to install the wing brackets... .

Trying to find a template for marking the underneath side of the trunk lid for a duster mounting for the wing brace...thanks

Where should the wiper blades be in the off position in relationship from the bottom of the windshield up....thanks

How hard is it to do the conversion. Any help would be appreciated. Thanks

On my driver side interfender there looks to be some kind of a relay that has a reset button of some kind. The wire from the proportioning valve goes up to this relay. Does anyone know what it is or what it does? Thanks!

Does anyone know the color and the location on the bulkhead connector at the firewall for the power wire that goes over to the fan motor? Thanks

When my wiper motor comes to rest when I turn it off I still hear a little ticking and the amp gauge jumps if I wiggle the wiper switch in the dash it will stop. Thoughts

I recently purchased a duster that has a 340 in it. Mild build mild cam 727 transmission 391 gears. It also has a stall in it that seems to be rather high. I noticed that it seems kind of lazy until you put your foot in it. Then it'll move pretty quickly. The guy I bought it from said that he...