Search results for query: *

Awesome original shape, no holes , light surface rust on some interior areas only. You can see what you are getting, not all bent up or dented. Marked as cuda but thats not correct. Louisville , Ohio. $600 for pair. No shipping or delivery figured.

Anyone know where to find a NOS fuel sending unit for a 64 barracuda . china repops are junk , improper ohm readings for mopar . need one real bad.

64 Cuda original 273 intake . Is there a way to defer some of the heat in the two areas left and right of the carb., without affecting warm up idle It fried my nice paint job in those two spots ?

Any one have advice ? got a new ring and pinion, carrier is only out by 1000th pinion is set to spec and cant get all the noise out of the drive side, marking ink shows them coming together nice. go figure ! had it apart 5 times now. Is there a spec or trick I don't know ?

I have a 64 automatic cuda anyone know where I can get a nice set of floor mats. My interior is gold with the darker brown-gold carpet. 1967 cuda is as far back as I am seeing. Would that be the same ?

Any body know if those were painted over with the car originally, or are they that plated silver color I see underneath. All I have seen in the past were the color of the car (most likely not removed when repainted). Not sure though. Thanks in advance for any replies, and MERRY CHRISTMAS.

Ok to coin a phrase ; ya got to think outside the box Certain suppliers (I'm not naming them) want us to use these new rocker molding clips that don't even come close ! the edge profile is all wrong and they are 1/8 " too long...half day of trimming 20 of these suckers and they still don't fit...

I have a 64 cuda. Some time ago there was talk on the best round headlights, can't find it in the search. Anyone know the best ones to buy ? thanks

The channel for the glass and attached ss divider strip seems awful wide (the channel on the inside latch side of door with the felt on the inside) when the window is partially rolled down or all the way down it is fine but when it is rolled all the way up there seems to be way too much play in...

The foam pieces pictured below came from the front lower fender area somewhere, Somewhere is the key word here. I made a note on a piece of paper but I can't understand my own description, go figure. I guess a picture would have been worth that thousand words. There is memory on them and I think...

Been way too long. Could someone tell me what should go back into the doors first. I would really appreciate the advise. I don't want to do anything twice. Oh it is a 64 Barracuda.

Any one got the bulb number for these?? I would appreciate it thanks.

They had a spring type clip in the hinge. ( to keep the seat from flopping forward probably when cramming on the binders!) I have two I can't remember ....one each seat on a particular side, or both on passenger side? See pic is this the way it goes in? Where does the pin go through...

Help ! not enough pictures upon disassembly which side for seals ? how does larger pan fit? Holy crap what a jig saw puzzle. PM me ? If you have time I would like to call someone that really knows how this goes together. Really need help here. pictures below.

Any one got a good source for " most like " original seat belt material. Mine are gold like the interior but frayed. All the back had was the straps to hook the seat down and no lap belt correct ?

OK, the post where the courtesy light is, the rubber does not quite meet the headliner about a third of the way down the post all the way till it makes the bottom curve, quarter inch gap or bigger. yesterday on a '66I saw a rubber/plastic trim piece in there that curved down to where the liner...

On the original rims, how wide of a tire can I use ?

Would the original tires have had a white wall ? Any one know ? My car is black wonder how that would look ?

Good Lord! I took no pictures cause when I took them off it looked so obvious to how they would go back on. Guess what ? Any one at this point in their restoration? got a picture ? Too much time passed. Probably too obvious that's why I cant get this puzzle.

The gas line from the carb to the fuel pump on a 273 automatic. It is 2 pcs due to the in line fuel filter . Are they the same for all 3 yrs. A company called "The Right Stuff" near Columbus ,Ohio does a good job re-doing lines in stainless, but all they show is '66. If they don't have the...

Ok I want to confirm the application of this seal. As you can see in the picture. Does that slight curve in the end profile of the molding(to the right where there is light glare) go around the lip across the top and sides? What about across the bottom? The detail on the car seems different...

Check this out, wow what a lot of work detailing the tape around those edges, painted those triangles 4 times till I got the result I wanted. They have a coat of catalized clear on them for uv protection. Pauls chrome in Cranberry PA, Those pieces were in fair shape when they got them though...

Ck out what I spent and look at the last item felts for $75 & how they did not fit in the previous thread, When i asked for my $ back ,,boy did I get backstroke ,,,been to long, already on vehicle, well I had to put one on to see if it would work#$#@@#$%% Make your own judgement on...

As you can see its coming, but nothing is cooperating very well, every time I go to do something there is an issue (kinda like life sometime) Who knows the trick to snapping these drip edge covers back on? I think I can deal with the extra mills of paint (as you might be able to see some has...

If I were remanufacturing these parts. I would make sure they are as original wouldn't you. Look below..... what a piece of junk I paid for two of these? This is the outside quarter window whisker, compare to the original...note the thickness and curvature of the end view . pushing on the glass...

any one know where I can find 2 nice red /blue ( valiant,early cuda), triangle logo buttons. The round ones that go in the center of the hubcap. They were notorious for cracking and the paint getting weak. Got 4 hubcaps getting professionally done ( dents out and polished).

any body know how it attaches, I remember a post quite a while back, might have even had a picture , can't find it. I know one end goes on the pin, but the other end made me walk....

I have 10 hubcaps, 4 originals and 6 from various swap meets. They have the valiant logo in the center cone (those are hard to find that are not all crazed), I had them all apart before I realized that 6 of the center most surfaces of the outer ss ring are high polished and the other 4 are...

Any one know where I can find these. The original I think had this extra metal flange. See picture.

Anybody got a paint code ? I believe it was close to hemi orange