Search results for query: *

I’ve been banned from Facebook for this 3 year old posting …

This corner trim looks like it had a stress crack when it was formed and the crack was repaired with brass. Has anyone come across similar repairs on metal trim?

The previous owner was a heavy smoker and the stains are hard to remove from the unpainted surfaces. I’ve tried alcohol; water based cleaner; and paint thinner - they all work but it’s a very slow process. Any recommendations for a fast working cleaner? I haven’t tried a solvent based wax...

I treated some rust on the interior of my dash with phosphoric acid, and then wiped off the excess before it dried but some of the acid is in a seam. There seems to be two trains of thought about neutralizing it: that it’s necessary and that it’s not necessary. I don’t want moisture in the seams...

I have a quick question. I was told to use an acid etch primer on plastic before painting but only if it’s unpainted plastic. My Barracuda has factory red plastic trim. Is it safe to use the acid etch primer on it or would that cause the red finish to bubble? Thanks in advance.

My plastic heater vents are chalky so I’ve gently sanded off the chalk the best I can but it’s impossible to sand into all the crevasses. The paint shop recommended SEM flexible coating paint. Do flexible paints stand up well to heat? The can instructions call for an “appropriate adhesive...

My ashtray was rusty so I dunked it in acid for a bit so the rust has been eliminate (except for the flash rust). Unfortunately the retaining clip didn’t survive. Should I drill out the two bottom rivets to separate it into two pieces before I paint it? The face will be black and the tray will...

My Braces for my 68 Barracuda are bent out of shape and I’d like to know the approximate angles that each end needs to be before I install them. Does anyone have a picture of a picture brace for reference, or the angles they need to be bent to?

I think they’re from a Mopar. They look like rocker trim but they don’t show any road rash.

I have a small damaged area on my dash and I was wondering what would be the best way to fill the hole. The hole is about 1/4” x 1/2”, and 1/8” deep. I thought I would dap on a thin layer of urethane glue, and then mist it with water so it foams, and keep doing that until the spot is level with...

One of lens is cracked on my fender mounted turn signal indicators. Does anyone make repops of the lens or do I have to buy new signal indicators?

I need bolts and fasteners for installing the front end of my 68 Barracuda (fenders, nose piece, valance, etc.). Is there a good Canadian source for the bolts, u-nut clips, etc, or do most members go through US sources?

Do most members install washers between the hinge and the body’s sheet metal when installing the hinge? Also what is the best way to install the push nuts, and how snug should they be against the hinge? I thought a deep socket might work the best to push on the nut.

I know it’s not from an A-body but this was in a stash of Mopar parts that I got. Any ideas what it is for or from? He also owned a 61 Seneca so it might be off that. The only number to if it a stamped number, “1663 1”. P Thanks

I have a 340 block dated 06-22-67, so that should make it date correct for a 68 vehicle. I can’t find a VIN on it or even a stamping pad for the VIN. Did they start stamping the VIN on the engine blocks at the start of production of the 68 models, or at some point after they had started...

I have to ship a set of magnum heads from Red Deer, AB to Winnipeg, MB. The heads were rebuilt and have low hours on them. What is the best way to package them for shipping? The shipper wants them in a box. I’m worried about the weight so the box has to be sturdy. At this point I might try to...

These brackets were among the parts that I got for a manual transmission setup from a 74 Duster (I think). Can anyone tell me what they are? Thank you in advance.

A friend of mine is looking for a set of Barracuda Slickback trim. So far he’s not having any luck and he thought a body shop could modify a set of side trim into some Slickback trim. Does anyone have pictures that show the profile of the Slickback trim? Thanks in advance

Does anyone have a drivers window for a 67-69 Barracuda N/B or convertible? The closer the better. I’m in Red Deer, Alberta.

Does anyone have a set of Slickback roof trim for a Fastback Barracuda?

1968 lower trunk trim. No clips. Good condition. Pictures show the two scuffs and stretched paint. $140 plus for the ride Located in Red Deer, Alberta

New gas tank. Was for my 68 Barracuda but I don’t like all the dents so have decided to buy a new one instead. Located in Red Deer, Alberta $100. pickup only but might be able to drop off in Calgary or Edmonton

Pair of rear interior side panels for 67-69 convertible. Need work or can use for parts. Located in Red Deer, Alberta. $40 for both.

I have some body panels that have rust or body damage or both. Since auto body work is not cheap, at what point should parts get thrown out? For example this 65 Valiant trunk lid and 69 Barracuda trunk lid.

my friends Dad has had this car console kicking around for a long time. I think it was from a van. Has anybody seen consoles like this? I’m not even sure who manufactured it

with Greyhound (western Canada) gone the way of the Dodo, it’s hard to find a shipper for large parts. I have to ship two bumpers to Manitoba but unfortunately the package is too big for Fedex or Canada Post. What does everyone use for shipping large items? I might also have to ship a door in...

it looks similar to a 65 Newport

has anyone tried a alloy wheel repair kit on damaged alloy rims? The filler looks similar to auto body putty but I was wondering if JB Weld would a better choice for a 1” square shallow chunk thats missing off one of the spokes.

i have to ship two 65 Barracuda doors and a trunk to the Maritimes on a pallet. What is the best way to load and fasten them on the pallet? Im concerned about damaging the door skins. I thought I'd place the doors on their bottom lips and then angle them towards each other, place the trunk in...