Search results for query: *

Looking for the right upper rear quarter and trunk gutter area from a Duster or Dart Sport. I have a new tail light panel and trunk gutter for the repair but need the top part of the quarter circled in the picture. Thanks!

Looking for the "Dodge" script emblem for a 1970 Dart trunk lid. Picture is of what it should look like. Broken studs is fine too.Thanks!

I am looking for a V8 spool mount (73 up) A-Body K-frame. Let me know what you have and how much you need for it with shipping to 95540. Thanks

I have been driving my duster daily, but its been getting too pricey for gas here, so I picked up this Slant Six powered 72 swinger to be my daily ride. I have always wanted another A-Body, it has only 60,900 miles (judging from the wear on brake pedal and other parts, I believe they are...

Any info would be appreciated! I am looking to improve the performance of the 360 in my 74 Duster. I took it to the street legal races last night and did good, but now have the itch for more power. I want to be able to keep up with the Mustangs that I raced. Here is my car specs: -Block...

My stepfather filmed a quick burnout I did in my Duster today. I just got finished installing a rebuilt suregrip in my car that I setup myself and had to make sure it works right. And it does!!! http://www.youtube.com/watch?v=nbTOgXcEt6A

I couldn't find a post on this already so here it goes: The drum brakes from 1973 and up 7-1/4 rear ends with Large Bolt Pattern will bolt on to the 8-3/4 rear without any hassle of fuss. People give these rears away either cheap or free, so you can just rob the backing plates (axles are not...

I bought what was suppose to be a rebuilt 742 case 8-3/4 third member. Suppose to have new bearings, rebuilt clutch suregrip and new yukon 3.55 gears. The seller said he bought it rebuilt and it sat for a year and never used it, then sold it to me. Anyways, I bolted it in this weekend, right...

I have an oil leak at the rear of my engine right behind the intake. I just installed a new Mopar distributor and an Edlebrock air-gap on my 360, and the problem didnt appear until after the install. I used the recommended gaskets on the sides, and only rtv on the front and back. I though it was...

I installed a TCI sizzler 727 in my duster. The question I have is, how late should third gear apply when you have the kickdown adjusted properly? I installed a 2500rpm stall also, 1st and 2nd gear feel great and shift nice. Right now, around town I dont even get into third gear as it is...

I though I would share a couple pic's of what I did today underneath the Duster. For three years I have wanted exhaust for my Duster, after my tax return came I got it!! I ordered it from Mayo Performance in Chino, CA. It's a TTI 2.5" system from the headers back. Came with Dynomax...

I am in need of a heater blower motor for a non-AC 1974 Duster. Mine is all rusted (the coils inside) and does not turn. Thanks!

I have been looking for a Heater bezel (standard dash) for my non-ac 1974 Duster. I have been watching ebay without any luck. It doesn't need to be mint, just ok for a daily driver (I can paint it if needed). Thank You

Sorry this is a long post, so bear with me. I am told I have to get rid of one of my vehicles, as I have lost my storage for one of them, and now have too many at my house. I need some input on this issue, as its a tough decision for me. I have whittled the choice between two vehicles (out of...

I rebuilt the suspension on my duster and set the ride height. The car looks like it sits much higher than before. I am going to get it the allignment set this Saturday, and need to know if I have it set close enough or not. The difference in measurement between the lowest point on the torsion...

I was rebuilding my calipers and found that the pistons are rusted in patches on the sides. I plan to order some calipers. Will 76 A-Body calipers work on my 74 Duster? I have slider calipers right now, are all 76 A-body calipers sliders, or is there a possibilty of ordering pin-type without...

I am putting my front suspension back together after putting in new rubber bushings (74 Duster). I have the passenger side done , but on the drivers side, the upper A-Arm doesnt fit back on the car very well. The passenger side went in as I expected it to, but the drivers side seems like its...

Does anyone know what size bolt and nut are used to attach the lower ball joint to the lower part of the spindle on a 1974 A-Body (Duster)? What grade bolt is recommended? I tore down the old suspension and am at the stage of installing the new lower ball-joints. The old bolts were rusted, and I...

I get a vibration in the steering at 40mph and and at other speeds above that. I think the 727 and 360 in my duster were split and now the external balance on the torque convertor is off. Is it possible the flex plate and convertor were not marked when they were removed and installed and now...

I want to re-cover the bucket seats in my 74 duster. The covers have worn and the foam is gone on both seats. It doesnt appear anyone makes A-Body seat foam for 1974. Will the seat buns they sell for 1970 and 1971 A-Body fit? Or is there a good source for replacement foam that I can cut to fit...