Search results for query: *

With regret I have to sell my long term project. It runs and drives well and can be daily driven as is. Presently it has a freshly built warmed over 318 with about 1000 miles on it. Carter AFB. Proform msd copy distributor w/ Msd 6al. Hedman short tube headers extensively modified to work on...

With regret I have to sell my long term project. It runs and drives well and can be daily driven as is. Presently it has a freshly built warmed over 318 with about 1000 miles on it. Carter AFB. Proform msd copy distributor w/ Msd 6al. Hedman short tube headers extensively modified to work on...

Looking for a rust free, preferably very straight left front fender. I also need the front valance in similar condition. I would buy n.o.s. if i could find them.

I have a 65 Dart. I installed 73 and later front discs and Jeep Grand Cherokee rears. I am in the process of finish installing everything and I am running out of time for our big 1000 car cruise / show in my city this weekend. My question is, can I use the stock drum brake master cylinder to...

These came off of a 8.25 rear end. The backing plates have been powder coated. Shoes, wheel cylinders and hardware are all new. These have never been driven on or had fluid to. I went to disc brakes. The axles are from an 8.25 rear end and are large bolt pattern. I have the drums too. They...

These are nice driver quality front seats out of a 65 dart GT. They do not need covers. The drivers side could use new bottom foam but can be driven the way it is. I also have the matching rear seat which is in even better condition. Asking $250 for the fronts, $100 for the rear or $300...

65 Dart w/ 318. Removing my stock manifolds to put on my shorty headers. The passenger side practically fell out. The driver side, not so much. I can get it out by just removing everything until it comes out. I'm hoping someone can offer up any tips to avoid unnecessary labor

These are Hedman Tight Tubes modified to work on early A body cars. For small block engines. I bought these here on this site. I have never used them. I got a killer deal on some Doug's so I won't be using these. They are coated. I'm looking for $350 plus shipping obo. Located in...

Hi everyone. I put a built up 727 into my 65 Dart Gt. It has the factory floor shifter. I really would like to keep the stock shifter if possible. I bought a 5 foot cable and bracket / shift lever kit from B&M. The problem is the trans won't get all of the gears using the shifter. If I pull...

I found one. I need a dipstick and tube for a 727 trans with a small block. I need something right away so hopefully someone local has one.

I removed my seals a long time ago. I'm finally ready to install the new seals. It just doesn't look right. Does anyone have any pics or willing to take a pic of an installed seal? Particularly towards the front of the car

Here is a link to the car. http://www.forabodiesonly.com/mopar/showthread.php?t=139993 This is a project car. I am willing to sell it many different ways. With or without the new rear end. With or without the new interior pieces. With or without paperwork. With or without an original 65...

Hi everyone, I am looking for a straight, un-bondoed, not rusty, front valance. It's the piece that the grille attaches to and the front fenders attach to. I am also looking for the plastic A pillar mouldings for the inside of the car.

I bought this Edelbrock TR5 from this site. It has two Carter 500cfm carbs. I was told the carbs were rebuilt and never ran. My project went a different route and I don't think I'll use this setup. I am asking $500 but open to reasonable offers. I will also trade depending on what you have...

This is a powder coated V8 K member I bought for my 65 Dart. It must be for year models 67 to 72 or so because it didn't fit my car. It's located in Riverside, CA. I'm asking $100 plus shipping or trade for a correct V8 K member to fit my 65 Dart. The one I'm looking for doesn't need to be...

These are semi-fender well headers. They are brand new and ceramic coated. $575 plus shipping or a reasonable offer. Paypal accepted. Located in Riverside, Ca. Here is a link to what they are http://www.summitracing.com/parts/HOK-5208-1HKR/ May consider trades. I need an A body 8 3/4...

I recently purchased a 65 Dart GT. It has a properly rebuilt 318 with all correct machine work done. It has rebuilt rods, new cast pistons, new valves and springs and has been balanced. It has some sort of unknown "RV" cam, stock exhaust manifolds, an Edelbrock Performer intake and a Holley...

I won a trivia question about the new Mustang and although it's Ford, this was a blast to drive. .016 reaction time 12.70 at 117mph. and yes.....I was wearing my FABO shirt! 00018 - YouTube

I have a 65 Dart Gt. It presently has a 318 / 904/ 7.25 combo. I have a completely rebuilt Sure Gripped 8.25 and a pretty stout 727 trans for it. I would like to keep driving the car as I install the new items. Can I swap the rear end without having to modify the drive shaft? If I have to...

Hi everyone, I'm thinking about replacing my fuel tank in my 65 Dart. It is the non vented style tank. Would it be beneficial to replace with the later vented tank and filler? Engine will be a fairly mellow 408 w/ electric fuel pump and 3/8" lines front to back. There is a possibility I...

Hi everyone. I need what ever holds the steering column to the dash. My car has nothing and the column just hangs down. My car has power steering and floor shifter is that makes a difference.

Ok, I'm going to try real hard this weekend to paint my engine compartment. My car presently is white and the engine compartment is too. I just looked at the Yellow car for sale ($25k, hmmmm, I don't think so). Anyways, it has a body colored engine compartment and people are poo-poo'ing it...

I am building a 408 out of a 360 block. I bought a Milodon 4 qt oil pan for it and a Melling pickup for my Melling high volume pump. I have done the oiling mods to the extent of drilling the passages on the block and matching the oil pump to main bearing cap opening. My question is.....do I...

Got the block back from the machine shop. They say the deck is 9.590. I am looking for around 9.5 to 9.75 c/r. I have 72 cc heads and could mill them if need be. So with the bore being 4.030, the stroke being 4.00, and the rods being 6.123, I am looking at KB-362's. These have a 19.40cc...

I'm collecting parts for my 408 build. It's primarily a street car with a very occasional trip to the track. I was looking a Speed Pro's Tri metal main bearings. Any thoughts on these good or bad , for a street application? Probably never rev past 6000rpm , maybe 300-500 miles a year...

I am looking for someone to widen my rear wheels and possibly narrow my fronts. I got an estimate from Custom and Commercial Wheel near me but I thought it was way too high. Stockton Wheel I think is out of business. Any ideas????

On my 65 Dart I have removed the front suspension for powder coating. I noticed on the LCA, on the part that rotates, there is a rubber bushing. Is there a way to remove the torsion bar pivot from the LCA?

I have 17 inch stock steel charger rims for my car and I want to use Rallye center caps but dont know if they'll work as the rims have no screw holes to mount them. I'm hoping to buy, borrow, or rent one cap so I can see if it will work. I have a daily U.P.S. account so shipping is no prob. Any...

Does anyone need this thing? Small bolt pattern. Not sure of r/p ratio but it is an open diff. Don't know condition but everything turns. Has brakes too. I can ship at buyers expense. I probably would give it away as long as it doesn't get scrapped(they don't make this stuff anymore,you know)...

Holley Street Dominator intake manifold. Came off a 360 engine In good shape. All threads are good. Located in Riverside, Ca No problem shipping Prefer Paypal $75 o.b.o (really don't know what it's worth)