Search results for query: *

part number P4532059 Includes thermostat and housing. asking $150 plus shipping

Thank you for all the information and keep it coming. Does anybody have any real life information on the Drag pack vs. Mod Man intake? I know the design of the drag pack is better but is it worth the extra damage on the wallet?

I am starting my own hemi swap, I have an 04 truck 5.7 as my base. I bracket race and this motor will only see the race track. My plan so far is to start with the stock bottom end, freshen heads with new springs to match a yet to be determined cam, mod man intake, and msd Hemi 6. It will be in...

www.aeicnc.com makes a motor plate that will adapt to a BBC water pump.

I did in my bracket raced 360, it beat up every piece of the valve train. Put the 292 purple shaft in and have had no more trouble.

Bump for offers, stuff needs to go gen3 hemi is on the engine stand ready to be started on

I use Crew Chief Pro as a log book and ET predictor, I think it works great when the car is tuned to follow the weather. Consistency and knowing your car are the biggest tricks in my opinion. Part of knowing your car is to know when to dial honest or hold a few in the bag. I am more likely to...

Fuel pump sold

Rockers are sold!

I am cleaning out the garage hoping to go in a different direction in the engine department (NEVER CHEVY). M1 dual plane intake very low usage $150 Crane 1.5 roller rockers with shaft and bolts like new. $300 Milodon gear set like new $200 Mancini pushrods for ball/cup ends part#...

That's not really a fair question, with E85 your water temp needs to be 170 when you stage, E85 turns to vapor at 172 degrees where gas turns to vapor at 68 degrees. We had some hot weather this summer over 100 one race day and I stage at 170 and come back to my pit and I was never over 185 and...

I have been running E85 for two years now with a 11.7:1 360 with a .509 hyd. cam and J heads that have been worked over a little. The fuel switch alone was worth .25 and 4 mph in the quarter. Current setup run between 11.28 and 11.32 almost all the time in a 75 dart sport. did my carb. Eric is...

I would lean more towards converter, Last year I rebuilt my 360 pump gas motor (9:1, .484 purple shaft cam, J heads) and stepped it up considerably. Fresh motor is 11.7:1 ported J heads, with a 2.05 intake valve and more cam (292/299 .508 comp hyd.) used the same converter that I ran with the...

Sorry for the delayed response, I haven't been on here in a while. The car weighs 3150 with me in it. Let me know if you have any other questions about it I would be happy to answer.

Working on getting garage cleaned up and I have a 750 E 85 carb that is powder coated black with green anodized metering blocks, works good very little run time great street/strip carb ($450). Also I have a 10" TCI streetfighter converter for a 360/904 combo that has 10 1/4 mile passes and 10...

check out http://www.horsepowerinnovations.com for E-85 carb. Eric is a good guy to deal with and knows his stuff when it comes to E-85. I just switched this year and I really don't burn that much more fuel than on gas. I also picked up .25-.30 and about 4 mph over gas.

Well after working out bugs for an entire racing season, The Best has been 11.45@ 117 with a 1.700 60 ft. Had to get a new converter, ended up with a tci 10" street fighter that stalls around 3200. Also ended up with a 950HP E-85 carb from horsepower innovations. There is no doubt in my mind...

I went from best of 12.08@108 in good air to 11.78@111 in similar air, with a mild 360 in a dart. That is the only thing that changed.

They are aluminum heads for a small block. They must be used on an R5 block. I am working on pictures

I have a set of P7 heads complete with titanium valves, new PSI springs, locks and retainers. Heads are fresh and ready to go. I'm asking $1000 for these heads shipped anywhere in the lower 48 states. Heads are in Kalamazoo, MI Will consider trade offers

I ran a .030 over 360 (77 block) stock crank, and rods. Stock replacement KB pistons 9:1. J heads gasket mached with 1.88/1.60 valves. Purple shaft .474 lift hydraulic cam, crane 1.6 rockers. torquer 340 intake and 650 double pumper. turbo action 10" converter stalls at 4200. best of 1.569 60ft...