Search results for query: *

Hello, I have a 1966 Formula S that at present has a set of the Super Stock leaf springs from Direct Connection. I am interested in trying to find an original set of leaf springs for my car. The build number of the leaf springs is 804 which from what I understand should be the last 3 digits...

I would like to find a set of original leaf springs for my car. They should end in 804 from what I understand. Thanks Dave

Hello, I have a 1966 Formula S that at present has a set of the Super Stock leaf springs from Direct Connection. I am interested in trying to find an original set of leaf springs for my car. The build number of the leaf springs is 804 which from what I understand should be the last 3 digits...

Hello, I am looking for some extra lug nuts for my 66 Formula S and interested in seeing who might have some that they might be ready to get rid of. These are the long lug nuts that go through the hub cap. You can reply here or send a PM. Photos would be appreciated also. Thanks Dave

Hello, I am looking for a 340 engine for my barracuda project. It does not need to be high performance but I am looking for a good rebuildable lower end with heads and brackets and pulleys (non-AC) if possible. Let me know what you might have. I am located in the Chicago area. Thanks Dave

I am looking for a set of the three plugs that plug into the bulkhead in the engine compartment. I just would like the 3 plugs so I do not need the entire wiring harness. If they have wires ends in them that is fine. I want a set without any broken clips. Let me know if someone has a set and...

Hello, I am getting rid of all my extra tail light stuff. I am located in the suburbs of Chicago. So what I have are 4 Driver Side bezels and 2 Passenger side bezels. Two of the drivers side bezels have been rechromed and I would say are good driver quality as they both still have some...

Hello, I have a 1966 Barracuda Formula S with an A-833 trans. I have the small yoke from the 904 transmission with the number 2530892 on the yoke. So after I restored my car and put the trans back in I had a leak at the rear seal so I replaced the seal 2 different times hoping that would...

Hello, I was looking at replacing the inner and outer tie rod end on my 66 Formula S and I looked up the Moog parts and came back with: Inner ES319L Outer ES319R Are those the correct numbers? I thought someone mentioned here before about heavy duty tie rod ends as it is a Formula S...

Hello, I am looking for the metal splash shield for the passenger side of my 1966 Barracuda. It is the small one in the picture. Dave

I am looking for the smaller of the two pieces in this picture. It goes on the bottom of the frame under the passenger side frame of the engine compartment. Thanks

Hello, I was driving my 1966 barracuda today and it started to rain. I turned on my wipers and they slowly went through 2 swipes and stopped in mid-swipe . I turned off the wiper switch and after about a minute the wipers went down to rest. I tried the wipers a few more times and noticed that...

Finished this last summer.

Just a question for clarification. I have a 1966 Formula S with the stock disc brakes and the original single master cylinder. I want to change to a dual master cylinder and through my searching found Cardone 10-3126M as being one that works with front discs and manual brakes. it says this...

I would like to find the adaptor that went on the top of the Master cylinder for disc brakes on a 1966 barracuda.

Hello, i was wondering if anyone had some pictures of what the original stud looks like for the master cylinder on a disc brake 66 cuda. My car has disc brakes with the reservoir adaptor but I do not believe it has the original stud. Does anyone make the gasket that goes between the master...

Hello, For lack of a better place to put these I will try here. Since you do wear these in the interior. I have two windbreakers from the early 70's The blue one has a patch that says Cuda Plymouth and the small label only says M. It has a hood and the following are the measurements...

I have a Edelbrock D4B manifold that I would like to sell. It is in very good condition, it does have a helicoil in one of the thermostat holes as you can see in the picture. It was painted silver as it does have a few blotches in the aluminum on the top. Underside looks perfect. I would also...

I am looking to trade my Edelbrock D4B manifold for a LD4B manifold. I would like to trade straight up as I do not need the manifold I have because I have a 66 273. I am posting pictures of my manifold. It has been painted as it had a few places of darkening of the Aluminum. The underside...

Hello, I have a 66 Barracuda with a 4-speed with the inland shifter. I wanted to know how to adjust the linkage rods. Specifically how do you make sure that all of the linkages on the trans are in neutral. I know about the tool to align the shifter so you can then adjust the rods, I am just...

Has anybody tried putting an AAR cuda exhaust onto a 1966 barracuda. I thought about doing it on mine using the regular exhaust manifolds for my 273 engine. Just wondered about hanging the mufflers and how it lines up. Thanks Dave

Hello, I am looking for an antenna for my 66 Barracuda. I need the entire antenna including all of the mounting hardware. Also i am looking for the spare tire board for the same car. It is a Formula S and I do have the cutout in the trunk fold down area because of the bigger spare. Is it...

I have a 1966 Barracuda and I am looking for a set of the nuts that are spot welded ( attached ) to the inner fenders that attach the top of the front splash panel to the inner fender well. They are square nuts that accept a fender bolt from under the inner fender well. When I got my car someone...

I have a 66 barracuda and I am looking for the bolts that hold the front splash shield to the inner fender inside the engine compartment. Thanks Dave I am also looking for a set of crank pulley bolts for the same car. 273.

I am looking for an original set of the bolts that attach the lower pulley to the harmonic balancer. I have a 273 engine, not sure if 6 cylinder would be different in terms of the bolts. I have a few of the bolts but I would like to complete a set for my car.:thumbup: