Search results for query: *

1977 440 block , heads , and internals plus six pack manifold with center carb . Decided to go 383 in my Dart so selling off my other engine was thinking of rebuilding . I think I have all casting numbers in the pictures . Someone drilled extra hole On flat below center carb but it effects...

so our old boat hauler inour yard is this old rig . We are doing the brakes and not sure how to get the drums off on the rear . Any help would be appreciated

this unit was on the car when I bought it , worked when car torn down 5 years ago . Shipping from 98250 and I have PayPal. Looking to get 90.00

This came with Dart I purchased . I went a different direction so don’t need . Shipping from 98250 , would like to get 350.00 .

trying to measure for disc brakes and noticed I can seat both . push 1 axle to seat on snap ring and opposite side pops out .200 . why is this happening ?

This engine has been out at machine shop forever ( my fault not there's ) since then I have acquired the 383 I'm am using for the Dart and also have a 440 project . Long story short I have no use for this any more so if someone could use it I am only looking for my bill total ( 583.00) plus a...

I recently purchased this 69 Dart with the leaf spring relocation kit almost complete . I have no instructions or paper work plus have never seen a finished product . Before I weld in the tubes thru the frame on the rear for the shackles is the a set measurement for how far tube stick out or am...

Nice truck with very low miles .truck spent it's life as weekend camper . The bed like new since 6 PAC sitting on it most of its life . Truck runs and drives great . All original power plant 383 , 727 , Dana rear . I have the original intake and 2 barrel carburetor .the hood need rust repair as...

looking for a set of rear shock mounts for a1969 dart 8 3/4 .

I am in the process of assembling my 8 3/4 but honestly don't know the if there is any shim process or set up for gear lash . I am a boat mechanic and boats don't have differentials Haha. Is there a book or website to go for assembly instructions ? I have an empty housing that has been narrowed...

I am removing the 2 Bbl carb and manifold and installing an Edelbrock Performer with a 600 cfm Edelbrock carb but am having an issue getting manifold to fully drop into place to get intake bolts in . The instructions have me putting an Edellbrock paper gasket over the intake pan . The manifold...

Just bought this very clean Camper Special , has 61,000 miles with a 727Torqflight and 383 . Will need a few parts and planning on upgrading the engine a little bit . I need a few interior pieces ( carpet , door seals and a windshield seal ) . Would like to put headers and new carb and manifold...

This car is a project and has to much rust for me to deal with . Beside the usual it has rusted out lower windshield seal area , kick panels , heater/ defrost box too . I have a title for the car , no fender tag , no build sheet . The 340 engine matches to vin tag on dash and rad support and...

My engine is being balanced and the harmonic balancer is junk , my 340 is a 1969 . Any one have one let me know . I am in the N.W , Washington , San Juan Islands . I have Paypal and will cover freight . It is a Forged Crank

I am getting ready to start rebuilding my 340 short block , it has to be bored .030 over and machine shop wants to have pistons before doing job . Just wanted to know if any one has recommendation ? The 340 is out of ( # match ) 1969 340'Cuda . I only have the short block so far but am planning...

Just read that Pastrana signed with SRT / Dodge to race Rallycross in 2013 Dodge Dart Rally car .http://www.freep.com/article/20120325/BUSINESS01/120326002/1014/BUSINESS01

I am selling the parts off my spare dash assembly . Plastic is in great shape , switches are stiff or stuck . Will sell with AM radio if you want it . I also have the dash pad and frame( both blue ) , wire harness if you would like to make me an offer . Vin on dash BH29F8B . Feel free to ask...

Well here are some photo's of my real rusty 340Cuda , the area around the door hinges and sill plates is real bad , floor panel is toast , heaterducts and windshield is rusty and has 3 holes windshield frame . Any advise is appreciated , is this car too far gone ? it is definately beyond my...

Just read on ESPN that Penske gonna switch to Ford next year , this really sucks if its true .

73 Duster slant 6 auto on craigslist Seattle for $400.00

Going to south sound tomorrow to buy another 69 Barracuda parts car . This one is a BH29F9B Fastback but i think i still may need 1 more car to restore my 69 340'cuda . The car i am buying tomorrow is too funny , it has a 318 1bbl with an automatic but i found it has a clutch pedal ( fender tag...

I live in Friday Harbor and am looking for a shop that can clean up and check over an old Chrysler 413 and my 69'Cuda 340 . The 413 is Ugly , I have it torn down but needs tanked and inspected for rebuilding . The 340 is basicly an ugly shortblock ( gonna need lots of 69 340 parts guys ) that I...

I have a 340 short block that came with my 69 340'Cuda but all i have learned from casting numbers is that it is a late 60's to early 70's 340 . Is there more to be learned from these Numbers .... 2780930-340-3 ..... ? then there is a stamped 9B310689 , does this mean anything . I will take...

Hello everyone , love the site and hope to be very involved , havent been able to do much restoration for 20 years ( 67 Coronet 440 ) but now that my bussiness is stable and the house is built I plan on a starting a new project . I just purchased a 69 340 'Cuda and it needs a lot of work . I...