Search results for query: *

Hey guys/gals I picked up a 1974 D100 a few weeks ago, looking for some wiring info. I am replacing all the wires on the engine harness and beefing up the charge wire, along with bypassing the amp gauge. Do anyone have a pinout or diagram of the firewall bulkhead, I’m cleaning and Replacing all...

Abody Mopar 4 speed setup Plymouth dodge 1300 or offer/trade Non overdrive 4 speed iron case aluminum bell housing. Transmission works good, I ran it behind a 360 in a 73 Duster for a few years, everything has same wear but still works good .I am now going 6 speed. Transmission is ready to...

LOCATED IN BUFORD GA 30518 Price $2200 Looking to sell my 360 Small block dodge set interested in trades for parts for a hemi swap 1971 block bored 30 over Big valve 2.02 j heads (ready to put on) Block has been machined and cleaned ready for assembly can bearings installed...

Ok so I got to looking and seeing what I could do as far as installing coilovers on a qa1 kframe. Going in a 73 Duster gonna have a small block, mostly street car. I found some coilovers with a stud mount in one end, and was thinking with a properly braced upper fender well would they work? I...

Ok so I’m at a point where I am redoing my engine bay, got most of it done other then the wiper hole. I’m gonna shave and mount a wiper motor under the dash. Looking for ideas on either just making a round plate and patching the hole or taking the whole area bump where is mounts out and making...

Ok so I have a 73 Duster I am building and at this point I need to put subframe connectors on and also going to do torque boxes. I have some 1/8 steel that I’m gonna use to make my torque boxes and was planning on doing 1.5x3 homemade connectors. I got to thanking and looking and I have the...

Ok I have a 360 73 duster looking at my kframe options car is a street/strip car I have a factory braced frame now with qa1 uppers and lower control arms. is the qa1 sub frame worth it over my stock one, or are there any other options. I want to stay torsion bar.

wrong area

Ok so I am wanting to build a hot 360. It’s going in a 73 duster 4 speed 8 3/4 with 4.10s and a spool. This is a street/strip, I am ok with it being a handful in the street. Car is manual steering and brakes. Now my power goals are around 425-450 with equal torque and a nasty idle. Yes I know...

Ok so my set up is 73 duster 4 speed with 83/4 diff just swap gears and ended up using a 489 case I did have a 741 case now it’s all back in the car I know the ujoints/Yoke is different the 489 uses a larger ujoint but what ujoint does it use

I have a pair of 15x10 cragar ss wheels they are 15x10 with 3.5in backspacing and 5x4 small bolt pattern they polish up good but crome is flacking around hubs/center of wheel tires not included looking to get 350 for the pair will ship at buyers expense located in Buford Ga

What will it take to mount my small block 833 to a 400 block I know bell housing need swapped but what as far as clutch/flywheel and z bar setup.

Ok so me and a buddy where at the dragstrip just watching and hanging out, he brought up a good question. My Duster idles pretty good hits super hard and lopes good but its a slow lope and most all the fast cars on the track have a very fast idle but hit super hard so my question is what specs...

Hey guys I am back I have been gone for awhile but things are going good. I have been working for the dodge dealer for 1 and a half now and they are treating me good and I am enjoying it. I still have the duster it has been sitting after the rings got so back it would not hold compression...

Ok guy I have plans for the duster and it involves mostly race limited street. My requests Small block Mopar 500-600hp range no forced induction I am waning to run nitrous on top of the 500-600hp The only reason I do not want to run a big block is because I have a 4 speed in the car...

I am selling my 1984 Dodge w100 4x4 This is my daily driver I drive it 40 miles a day 6 days a week with no problems. What it has 35x12.5x15 Cooper tires about 1100 miles on rears 800 on front still have blue paint on white letters dana 44 front axle manual lockers 9.25 rear end with a posi...

Well I ended up getting another truck its a 1990 w250 5.9l cummins 4x4

I have a brand new in the box RPM air gap intake bought for the duster but plans have changed and need the money for another project. Looking for 270+shipping

Ok the 318 in my truck has done well and still doing well but getting old. its a 84 318 now I will be mostly daily driving and off-roading (a lot of off-roading) and pulling my duster to the drag strip. I don't want to swap pistons but rering and rebuild everything else. I figured some type...

Ok the 318 in my truck is slow to build oil PSI when it cold of when hot take about 5 sec to get to the center of the gauge. Once it get up to the right psi it fine does not fall much after driving. I am running 10-40 now will it help if I switched to 5-30. I plan on freshening up the engine but...

I am selling my 1984 Dodge w100 4x4 This is my daily driver I drive it 40 miles a day 6 days a week with no problems. What it has 35x12.5x15 Cooper tires about 1100 miles on rears 800 on front still have blue paint on white letters dana 44 front axle manual lockers 9.25 rear end with a posi...

Ok so I am thinking about pulling the heads and doing a vale job and seals in my 318 on my truck I have a old 4bbr intake would switching from a 2bbr to a 4bbr with a 500cfm carb really make any difference.

Ok I was wanting to know if anyone know about the NP208 transfer case. The t case in my truck 84 w150 work fine other then it will not go into 4lo. I have read how to adjust the linkage but also read that in these t cases if 4 lo is not used often it can rust and not allow it to work. When I...

Ok so the Dana 60 in my truck is loosing the lock it spins both rear tires for a few seconds in a mud hole then only one. Also how make a good spool for a Dana 44 for the front axle. If I change fluid and put additive in it will if help the rear end of do the clutch's need rebuilt.

do they sell smaller pulleys so mu alt will charge at idle

I was wanting to ask how do you remove the rotor on a 84 w100 4x4 truck. It looks like you have to remove the but to get the rotor off but I cant get it off is there something else holding it o .

Does anyone know of a good classic dodge truck fourm

Just went and bought this my new daily driver 1984 w100 4x4 318 auto drove it home hour and a half no problem steering box has a little play but not bad. Needs brakes on all 4 wheels but that's no big deal.

Whats a good Dizzy for a mild built 360 to run with a msd street fire or 6al box.

Ok I have been running the Skip white disturber for a while about 5000 miles and my coil just went bad and left me on the side of the road. The thing is I put a new MSD Blaster 3 coil in when I put the dizzy in so 500 on the coil and the dizzy. When I pulled the cap off the rotor button was 100%...