Search results for query: *

  1. G

    518 46rh help please

    Ok, as you can see my time is limited. Today I went to the local LKQ and pulled a VB. It looks like a virgin that has never been tinkered with. I came home and put it in. I get 3rd gear at around 50 mph. So I might have a governor issue or a cable issue. So I’m somewhat happy now. I don’t...
  2. G

    518 46rh help please

    Air check is good I’m looking at the release pressure on the big bore or the front servo. Air check only checks the small bottom bore, moving the pin up correct? Last I checked before the 2nd tear down was 65 in forward gears. Possible timing issues with the rigid front band. I set it at 2...
  3. G

    518 46rh help please

    It’s all back together. As of 10:30 tonight. Test run on the lift says still no 3rd and I think gov pressure is still low because 2-3 shift doesn’t happen until 36mph. At that point you feel it happen then speed starts slowly dropping. At idle I’m at 22 mph in 2nd gear. I’m pretty sure with no...
  4. G

    518 46rh help please

    It’s out and the verdict is in. The reman pump assembly bolts were never tighten. They backed out a couple turns. Not allowing the stator assembly to seal against the pump assembly. Now back to the 2-3 shift issue. Them Teflon seals are getting replaced with the ones in that came with the kit.
  5. G

    518 46rh help please

    Well it’s been busy. Today was the day I pulled the OD housing off inspected the Governor every way imaginable. I even put a sonnax governor valve in it. The new and improved. Put it back together and seen a spike of maybe 35 while goosing it on the lift. Still 14psi at 25mph and no 3rd shift...
  6. G

    518 46rh help please

    Reverse is firm and solid. That was one of my reasons of tearing that valve body back apart was to check that ball. I had read that somewhere before. Will have to get od housing back up and check reverse pressures. Yes TV cable is maxed out at Wot and loose at idle.
  7. G

    518 46rh help please

    This is in my 95 ram. It’s got 2800 stall converter Red alto power packs in the direct and forward clutches Reman pump with stator shaft. Solid front band 3.8 lever Fresh rebuild with transgo tfod hd-2 kit installed. I have a no 3rd gear condition. Clunk seems to be there but not shift...
  8. G

    Fitech issues

    Well I did something right yesterday. I got my 9 year old son cranking while I hit it with the timing light I found where I was which way way off and sparatic. With him cranking and fuel disabled I found where I was and popped the cap off I was almost off #1 and close to 8. So I moved the wires...
  9. G

    Fitech issues

    Your build was what made me chose the Fitech instead of going blow-thru. I’m running the 600pa. With FiTech’s 340lph e85 pump. I wanted to leave that option on the table. My setup is very similar to yours if I remember correctly. Stock bottom end re-ringed and new bearings. Hughes Eq magnum...
  10. G

    Fitech issues

    Just long enough to reach the distributor.i think I had to add a few inches to reach. No slack. One thing I didn’t think about is I had the battery charger on it the whole time. That could have contributed to some noise. Alternator is not connected. I could try adding some grounds as my battery...
  11. G

    Fitech issues

    Checked the slop no issue there. So I went about halfway back to where I started set base time at 10 deg. Fired up and tried to idle. Got the timing light out started again and shot the balancer. Showing about 6deg on the balancer. But I would get an erratic spark here and there. Late spark...
  12. G

    Fitech issues

    Maybe I said that wrong. Only after it’s up and running and I have windowed a cap will I play with moving the reluctor to phase the distributor. That is not my first step in fixing the current issue.
  13. G

    Fitech issues

    I got some ideas to test. Thanks guys. I really think the fuel pump PWM screwed the pooch on this one. I didn’t change it to 100% after I started messing with the dizzy. As soon as I can get some garage time I will update. Afterthought is I should have set up without timing control but running...
  14. G

    Fitech issues

    So here it goes dumb it down for me. Anybody care to share their base timing for a 5.9 magnum. I set it up like I would any distributor rotor dead on#1.-10 on the balancer and -10 on the controller and starter was kicking back. Changed to 0 on controller and still no fire. Still fighting with...
  15. G

    What guide plates are you guys using on magnums?

    That was my thoughts was to elongate rocker stud holes side to side. That way I could line them up and sockem down. They are not toed in or out just shifted to the right or left.
  16. G

    What guide plates are you guys using on magnums?

    I guess I should have mentioned I’m running the Hughes EQ heads with the 5/16 rocker conversion studs. The ones in that link are made by Edelbrock for there 3/8 studded heads. Years ago I ran the crane kit that had a stud with a rectangle metal piece with a nylon insert with a hole for the...
  17. G

    What guide plates are you guys using on magnums?

    i bought a set of comp cams and the alignment is horrible for a non adjustable guide plate. I am thinking about elongating the holes on the mill to get these straightened out.
  18. G

    8/6-8/11 Mopars at Myrtle Beach SC

    Yea it was a wash I ended up not going several days. The weather wasn't as hot as it usually is. I just figured there was more to do then go see the same 5 cars everyday. I didn't waste the gas to drive to darlington to be let down.
  19. G

    8/6-8/11 Mopars at Myrtle Beach SC

    Sure hope some more mopars show up in the next few days. There was only 2 cars at hooters when I rode by at 4:30. Last night at hard rock there was maybe 12 cars mostly new challengers. There was a dart swinger in the mix though and a very hairy guy in a ford powered cobra kit car that...
  20. G

    North Myrtle Beach House for Rent 8/6-8/11

    Just a last minute bump. Also I am here in myrtle beach for anyone interested that wants would like to check it out.
  21. G

    NEWBIE From Greensboro, NC

    What part of Greensboro. I'm in NE Greensboro. Hicone/summit ave area. 75 dart sport here. It's a little rough around the edges since I've been focusing on building my garage. Shoot me a Pm and stay in touch us mopar guys are hard to come by.
  22. G

    North Myrtle Beach House for Rent 8/6-8/11

    My family Has a Beach house on 707 28th Ave North Myrtle beach that is open for the week of Mopars at Myrtle Beach. So I figured I would see if there was any Interest. 3 Bedrooms 2 Baths with Fold out couch in the Living room. 105$ a night. I have a pic on My phone that I snapped of there Flyer...
  23. G

    8/6-8/11 Mopars at Myrtle Beach SC

    Anybody going? I will be down there on vacation that week anyways.
  24. G

    Looking for a Spool mount V8 k frame NC-TN

    Im leaving out tommorow morning driving to western TN hoping somebody might have a K frame to fit a 75 dart sport that I can Purchase. Leaving out of Greensboro NC Heading to Savannah TN.
  25. G

    What will I need to put my /6 in a truck

    Well that puts a damper on things. That's to much trouble just to put a slant 6 in I was just going to use it to putt around in but. For the trouble I could just get another small block. Thanks
  26. G

    What will I need to put my /6 in a truck

    I have a /6 in my 75 dart sport that runs great. I have a 73 d100 custom that has a 318 727 combo that does not run so great. I tried selling the slant 6 but dont want to give it away so im going to use it and put the d100 back on the road. What all will I need to put that /6 in the truck while...
  27. G

    A/c manifold gauge hookup questions

    High side is always the side which has the smaller hose going to the condenser . It's no big deal if you hook them up backwards. Other than you will lose a little refridgerant switching them back. Why not retrofit it. If. It's not working you probably have a leak. R12 is pricey if you can find it.
  28. G

    A little pricing help on 4 speed stuff

    Sorry if this ? Is in the wrong place. I just bought a 75 dodge dart sport it has the slant 6 a-833 4spd overdrive transmission. I want to sell all this 4 speed stuff it runs and drives with no grinds. I want to sell it all pedals to driveshaft. I will even cut the hump out of the floor but what...
Back
Top