Search results for query: *

I tend to agree. Besides, in ‘71 and ‘72, who thought there would be any of these things left in 50+ years.

Thanks Carl. I’ve taken this car to three shows. Two people knew what it is. One guy thought it was a mustang! Very few of these around. Want to keep it as stock as I can. I should have taken measurements before I started the restoration. I just kinda revel in the fact that it’s my first new car. .

Thanks. I appreciate it.

I started studying these pictures to place my emblems and do not see a legend to decipher the numbers on the fender nor tail panel drawings. I don’t have the body stripes but need to determine placement for fenders and tail panel. It is not a 340 car. On the pictures you have, did you see...

PERFECT! Just what I was looking for. Thanks so much.

anyone know where I can find info for the proper location of front fender and tail panel demon emblems for this car? I would rather use measurements than just guess. Thanks in advance.

overheating issue resolved. I found a machinist locally who made me a very nice 5” water pump pulley which has increased my fan speed to the factory recommended 1.3:1 water pump pulley to cam shaft pulley ratio. Also added hood to radiator coil seal, replaced the water pump, and added a radiator...

“It is possible to put the longest bolt in the wrong hole and drive it into the outside of #1 cylinder and to crack that cylinder, sending coolant forever into that cylinder. ” If a cylinder is cracked and getting coolant in that cylinder, won’t the car run rough? Would not the compression in...

I know this is an old thread, but I have to make a lower radiator hose on my 71 demon and saw here where you have a custom made tube. Can you share how you made that? Thanks.

I know this is ancient history, but what kind of “plastic bottle” rig did you set up? I want to add one to my 71 demon. The radiator overflow tube goes towards the driver side, where the battery is also installed so there is little space. Thanks Al Graham.

Thank you. I’ll call them tomorrow.

i am having cooling issues at low speeds/idle and am looking for a 5” water pump pulley. Where did you get a 51/4” pulley? The shop manual for my 71 318 and a/c calls for a fan to crankshaft pulley ratio of 1.3:1. My current set up gives me a .92:1. I want to leave the crankshaft pulley alone so...

Thanks to all. Starting at the beginning.

Thank you. I’ve done that and been reading for five days.

It overheated the same but lower temps. I replaced the radiator and added an NOS fan shroud. That was four years ago. I’ve hardly run the car since. These numbers are at least 20 degrees higher. I am going to measure the fan tomorrow, but it is a more stout fan than the original. When you say...

I have a 71 demon with a 318 engine and three speed transmission. During a restoration the engine was rebuilt. Modifications to the engine included a performance cam, Holley 4bbl carburetor, electronic ignition, and headers. I had some initial issues with engine overheating especially when...

I got seat covers from them. They look just like the originals. They look great installed. I bought the door panels from year one, but turns out they were made by legendary too. I wasn’t aware of that when I got them. They look great too. Just my two cents.

Did you ever resolve this issue? I notice no one responded to your post. My seat on a 71 demon is not wanting to go back and forth. I have the body service Manual that does not address adjustment nor repair. Thanks, Al Graham.

Mike, It would be great if you could post a few pictures of your setup. Upper and lower attachment points would be much appreciated. Thanks, Al graham

Moparmat. Do u remember what car the blue one is? Did u have to modify anything to install the set? The picture looks like the roof rail point is further back than the retractor. I have a 71demon and a set of mx three point belts I want to install. I am getting conflicting info as to whether...

Can u tell me exactly how you did that? Did it require welding a new mounting point? Thanks.

I have the same belts for a 71demon with bench seats. How does the retractor fit at the sides of the floor. Mine are huge and have been delaying installing them til I could talk to someone who had them in. Can you possibly post a picture of the setup? Thanks. Al graham

Was there a lot of resistance getting the clips seated? I’m a little concerned about them showing through the vinyl.

Thanks. Sorry for the delay. I appreciate the pictures. Huge help. Did you find two thicknesses of board in the door panels so the clips go between them? Going to tackle them next. Carpet nearly done.

THANK YOU! These are perfect. What blue is that? Mine is B5 blue. I’m intsalling carpet too. Did you fold yours over the sill plate? Did you have any issues installing clips on the panels? They look great. Thanks again.

im trying to get my 71 demon back together. I thought I had pictures but as usual, was wrong. Can anyone post pictures of the interior that will show the rear panel (under pop out window) to the floor and then along the sill plate from the inside so that I can see what is supposed to be where...

Thank you. I am nearly finished this car after only about 15 years! I started out going to go to earl scheib. Will get some to finish and continue looking. Thanks again.

anyone out there have a vendor for correct color door jamb windlace for a 71Demon? I found one mopar vendor who has it but no listings for models after 1969. Any info is appreciated. Thanks.

I looked on their site. They do have them for bucket seats. Will call today. Thanks guys.

am replacing upholstery on 71 Demon. Anyone know of a source for molded foam for a split bench front seat? I only find molded foam for buckets. I don’t even know if that’s anything that’s even made. I’m mainly looking for application for the seat back, not necessarily the bench. Thanks.