Search results for query: *

anyone know where I can find info for the proper location of front fender and tail panel demon emblems for this car? I would rather use measurements than just guess. Thanks in advance.

I have a 71 demon with a 318 engine and three speed transmission. During a restoration the engine was rebuilt. Modifications to the engine included a performance cam, Holley 4bbl carburetor, electronic ignition, and headers. I had some initial issues with engine overheating especially when...

im trying to get my 71 demon back together. I thought I had pictures but as usual, was wrong. Can anyone post pictures of the interior that will show the rear panel (under pop out window) to the floor and then along the sill plate from the inside so that I can see what is supposed to be where...

anyone out there have a vendor for correct color door jamb windlace for a 71Demon? I found one mopar vendor who has it but no listings for models after 1969. Any info is appreciated. Thanks.

am replacing upholstery on 71 Demon. Anyone know of a source for molded foam for a split bench front seat? I only find molded foam for buckets. I don’t even know if that’s anything that’s even made. I’m mainly looking for application for the seat back, not necessarily the bench. Thanks.

Am looking for an upholstery shop in town familiar with Mopars. Anyone had experience with any here? Both good and whom to avoid will be appreciated.

I have 5 14 x 4 1/2” 5 on 4” bolt pattern wheels off my 71 demon. I bought the car when new but have restored it and put on disc brakes. They are not show quality but straight and undamaged. Enclosed a picture of one. Seen one you’ve seen them all. I have no use for these but want to keep them...

i need to replace the upper radiator hose on a 71 demon 318 engine. The old hose is a 1 5/8 ID hose. After two days calling and visiting every local auto parts chain and on multiple web sites I am unable to find such thing. Everyone insists the hose is 1 1/2". It is not. Any ideas for a source...

note the space between glass and weatherstripping. Any ideas what went wrong and how to correct? Thanks

on my 71 Demon, can anyone tell me how to position them on the studs so they are correct without trial and error. Also, what blades are you guys using? These are angled at the blade end. Also, how do I straighten the arm long enough to place? Thanks

i am completing the interior on a 71 demon. As I go to install the door emblems, I notice there are cylinder shaped fasteners that go on two posts on each one. Those go through a hole in the door, securing it. Anyone with knowledge as to how to install them safely? These things are 46 years old...

i am investigating installing the above in a 71 demon. Everything I see says to remove the ballast resistor. So I decided to see what would happen without the resistor. With the ballast resistor connected I have 12 volts with key in on, start, and accessory positions. With it disconnected I have...

I put a points to electronic ignition conversion kit in a 71 demon w a 318. Am considering an HEI distributor. Anyone done this? How involved was it? What product did you use? Thanks.

in 2008 I replaced my 1971 dodge demon points ignition system with a Mopar Performance Electronic Ignition Kit. Part number P3690426. This worked well but has failed. There is no power coming from the distributor. I am told that I can replace the contents of this entire conversion kit with an...

i have above kit installed in a '71 demon 318. It has historically run fine. It sat for probably 6 months w trickle charger. It now has no spark/ no start. Turns over fast but no go. Battery, coil bench test ok. Any suggestions as to how to troubleshoot and fix? Thanks guys

I want to replace my factory lap restraints with a good three point system. Any advice on which company to use? Thanks

Picture # 1 is the original window off my 71 Demon. Note in #1 top right (a) there is a sizable gap. This has been this way for as long as I can remember. At bottom rt (b), that rubber is extremely brittle. The remainder of this rubber is stiff, but probably serviceable. Is this rubber...

I am replacing the rear 1/4 pop out window weatherstrip. I want high quality that will fit and are correct for my car. Can anyone steer me toward a source that you have been particularly satisfied with? Thanks in advance alg

Had someone told me about this I would not believe it. But I did this myself and have a reliable witness. The driver side door of my '71 Demon is low at the end opposite the hinges. I looked around and spoke with the man who did the body work on the car. This morning a friend of mine and me put...

I am driving a 71 demon with a 318 engine, 3 speed with a stock 22" radiator(new) and a 17" 7 blade fan. I have an autometer temp gauge that is accurate. I added a shroud last week. I have also installed an a/c from classic. The car heats up nicely to 180 and stays there unless when am stuck...

I have a 71 demon. I'm original owner. I have had it restored. The shop manual I bought the year I bought the car describes an elaborate(I suppose for the year) fuel vapor saver system. My car never had this. Of that I am certain. So I fill the car and gas runs all over the place. I have found...

Am nearing completion of resstoration of my '71 Demon. In the attached picture the area rear of the chrome strip to the end of the door looks unfinished or incorrectly installed. Besides that, it leaks. Any suggestions/thoughts for fixing are appreciated.

We rewired my 71 Demon. it has a new speedo cable and was operating properly until I reconnected it to the instrument cluster. Now the speedometer needle goes from 0 to about 80 as the car moves forward slowly. I disconnected it and assured that the cable is centered in the connector so that it...

anyone got any ideas how to remove the latch mechanism off glove box door on a 1971 demon without damaging the plastic trim piece behind the knob? thanks for any help al

any suggestions on how to install the over center spring on a 71 demon? i had to replace the bushings and sleeve. thanks al graham

I need a pair of brake pedal bushings for my '71 Demon. pretty sure they are nylon or neoprene (white in color). they are .812 ID and .875 OD.and about 1/2 to 3/4 in long. i have struck out at the google search as none of the folks i contacted have them. once i find these I can complete assembly...