Search results for query: *

Thanks for any help, need get my Valiant moving again without having to reach up under the dash to move the lever.

I need to install rear belts in my vert. I have located the where now I need to order some and can't seem to find the length needed. What length is normal for these? Thanks.

Hi everyone, I scanned to how to articles and have read many posts. I have the shop manual and can see the instructions, I am not a dense but from all accounts on this forum the project is a bear to do laying under the car. Really worried I will bend the spring in there trying to get the...

Rubber Gasket Wanted - 1964 Valiant - Driver side tail light housing to body gasket, the think black rubber one. Thanks.

On my 64 tail lights, when I removed them, there was some black putty like substance that presumably looked like it water proofed them to the body. Any idea what that stuff is called and where can I get it. Working on getting the rear end water proofed. Also, there was a black rubber gasket...

I need to put some lap belts in the rear of my vert before I drop the interior into my project. What length do I need to purchase? Thanks.

Today it is finally a driving/rolling restoration! Thanks for all of the information I have gained here! Many of you have been and will continue to be a valuable resource.

Hi, I am looking for passenger side lenses for my valiant. 1 Red tailight lens passenger. 1 clear reverse lens passenger. Thanks.

I am looking to to see if anyone has an odd set like I need or perhaps I can peice a set togther. For sbp 5x4 not uni-lug. 7/16 shank 15 right and 5 left. Trying to avoid pressing out the 5 left handed front studs. Thanks.

So the car is finally running again after nearly a decade long restoration. However, it is running rough and now I see that fuel is leaking out of the carburetor. The carb is on a 1964 225 /6 and was rebuilt with a kit (dont know which brand). It is leaking fuel from the bowl vent valve...

Just need the pin only and boot if possible, have all other parts including a good trunion. Shipping to 92346. Thanks.

Hello FABO, what would be the best way to repair this wire? There was an L angle fitting that slipped over the threaded stud on the head, the L fitting is long gone. http://www.forabodiesonly.com/mopar/vbpicgallery.php?do=view&g=9959 Thanks.

going through a bag of parts that came with my valiant, please help me figure this part out, i.e., what is it, where does it go, can it be fixed or another ordered as the wire is no longer attached. Thanks. http://www.forabodiesonly.com/mopar/vbpicgallery.php?do=big&p=38802

need one to fit my valiant. engine is a 1964 vintage 225 (short tube and stick). shipping to 92346. Thanks.

Please help. I am putting the car back together and can't figure these 2 parts out. I have flipped through the service guide and parts manual but just can't seem to figure these out. 64 ply valiant sig 200 vert 225ci 1bbl carter no a/c. Thanks.

Any ideas on how to repaint the white on the black dash bezels (heater-fan- def, etc.)? After cleaning, I was thinking of taping off everything except the small section where the lettering remains and spraying with a can of white paint, then immediately wiping the excess area with the...

Hi, The oil pan is going back on today or tomorrow after real seal replacement. I have read the sealing oil pan instructions and am ready to tackle that in the right way. The engine is on a stand and I will put the pan back on with the engine inverted. I have a number of oil pan bolts in a...

Hi Everyone, I am looking for some tips and advice on reassembling my trans to my engine. I purchased a 1964 specific seal kit from Pat Blais and did that work. I didn't take the engine and trans apart (someone else did) and I am not sure of the best way to approach this. I have the 64...

Help needed please........Sorry if this has been asked before, a search did not turn up what I was looking for. So the bolts that attach the engine to trans are not with the car and I have no idea what I need nor what goes where. I am ready to put engine and trans back in the 64 Valiant...

Hi, I am looking for this part number 2290891. It is the steel lawnmower cable that runs behind the dash from the knob to the passenger heater box. It has 3 prongs for connections and switch turns to operate the blower. Thanks.

Car is in the paint shop and it will be back by end of December. There is no way to straighten or polish my grill without taking it apart so today I drilled out the rivets and it is in about 20 pieces. Currently the bumpers are being done and the chrome shop says $400 to rechrome the whole...

Hello, I am looking for a couple decent lenses, clear reverse and red tail for the passenger side of my Valiant. Thanks. Shipping to 92346.

Hi, I am looking for the chrome latch hinge combination that has the pin which goes through the vent window frame. That's for any help. Shipping to 92346.

I am looking for the small cylindrical part that holds the seat back and cushion in place, if anyone has one it would be greatly appreciated. Please PM me. Shipping to 92346. Thanks.

Looking for this part if any one has a good one with little or no pitting. Driver Vent Window Bracket/Pivot for 64 Valiant Coupe/Vert The glass on mine is fine, just the chrome pivot bracket and handle. Thanks.

I need a pulley crank bolt for my slant. Anyone know what size and depth this thing is? Thanks. http://www.forabodiesonly.com/mopar/vbpicgallery.php?do=view&g=7035 Mods, I put this in the wrong section, please feel free to move.

signet 200 convert body style. I have 19 plastic clips and 16 plastic cylindrical buttons to hold the clips in place. I need a couple more clips and a number of buttons. Anyone know where to get these? Help much appreciated. Thanks.

Hi, everyone, finally sent my 64 valiant to paint, have owned it for 20 years now, wow where did that time go? Will post some pictures soon. Currently I am looking for straight rear bumper brackets and rear bumper. Also: signet 200 fender emblem driver door handle (actually just need...

My 64 Valiant Signet Vert is WW1 (white Ditzler code 8358 ) and interior is red (Ditzler code 71203). I'm trying to replicate the original colors for paint. Right now I am working on the interior red and was wondering about how to deal with matching? I understand that I need to go with a...

Looking to replace the turn signal switch on my 64. Auto trans & manual steering. Column currently out and has a broken switch as in cracked with no chance of repair IMHO. Anyone know if these are available? Part number? How much? Where might I get one? Thanks in advance.