Search results for query: *

yeah, 8 cracks between the two. I have been hunting craigslist and letting people know we are in need. lol

Thanks. Its been a slow process. I just heard from the machine shop that my heads are garbage. so on the hunt again.

Wrapped up the weekend by mating the tranny to the short block and then stuffing it all back in. Then hung the hood and did a final adjustment on the front clip. I finally feel like we are making progress. The heads are at the machine shop,and everything else is clean and ready to bolt on after...

Ok, we have been moving along. a few months ago we got the front clip prepped and jammed, then yesterday and today we got the front clip hung, and the short block assembled and painted. tomorrow we hope to get the tranny mated up and the engine/tranny installed. Its been a long slow road....

Sorry, 7 and 1/4 rear end. Just wanted to make sure people new what bolt pattern I needed. Thanks

Just what it says. The small bolt pattern 14 inch rally wheels like on our Duster in my avatar. TIA, Sam

Sorry for dropping off the end of the earth. We were closing on our house and at the last minute we had to do a ton of repairs to make the lender happy and that was just the start of a nightmare three weeks, then my youngest son spilled a glass of water on my new laptop, then my oldest son had a...

Ok, new ECU is in, and we have fire !!! but...only in start position. As soon as the key is released, it dies. So NOW which wire is not hooked up right. lol

Cool Cuda ! The other thing I was thinking about was my midddle sons 65 Mustang. We will have a leftover 66 parts car, and i was thinking about ordering a Mustang II front kit for it....and having it set up for a 318. :-)

Thanks for the tips. I will report back tomorrow after installing the new ECU and ground wires with star washers and bolted through the fender....(sigh) lol

Ok, I have been working on my latest acquisition, a 66 dart. While going in and out of the garage, I kept going past my Hemi. I finally looked down at it and went "hmmmm". Then I laughed, but I kept thinking "what if". So I decided to ask the collective to see if anybody has put an old school...

Ok, ballast resistor checks out just fine, as does the voltage regulator. Keyed battery sources all check out correctly. I have a new ECU showing up tomorrow. If that does not take care of the problem, I will check the reluctor. I will also run ground wires to the battery from both boxes. What...

Cleaned all of my grounds and still no spark. No power coming out of the little blue box and going into the dist. So can anybody tell me if all the terminals on the alt are doing what they are supposed to do, and what is the little silver module next to the blue box? I dont know anything...

Need one more very important part. A driveline with yoke and rear u-joint bolts. This has a 7.25 rear end and floor shift three spd. TIA, Sam

Ok, I just read this thread and it answered some of my questions. http://www.forabodiesonly.com/mopar/showthread.php?t=234343 I will make sure the little blue box has a good ground and retest for spark. Here is what I have found with my latest purchase, someone put a later model 225 in...

Thanks for the info. Seems like everytime I do a search for 66, I come up blank. lol

I am in need of a stock steering wheel, complete setup, the molding on the leading edge of the hood, and both front fender moldings. Also testing the waters for a set of bucket seats/console shift. Thanks, Sam

Just brought this home last night. slant six/auto/bench seat car. Had a few questions about it. I am in need of a stock steering wheel, complete setup. This one has an aftermarket wheel in it and it shorted out the horn wiring. Is it a 66 only steering wheel, or are other years the same. Also...

Down In Lusk, WY Working on a 71 Duster with my oldest boy, got rid of a 64 Barracuda project, and just brought home a 66 Dart Gt

Hopefully get Ians Duster done over the winter, but also get two bedrooms built in the basement and get some time in on the model bench. :D

I guess you missed the original post. The 360 flywheel will not fit the bell housing because the 360 flywheels are larger diameter. So the best thing for my application was to have the smaller diameter 318 flywheel drilled for balance, now everything will bolt up and be balanced. Hope that makes...

I was going to update this thread myself. lol Just got the flywheel back friday. Our "local" machine shop is 100 miles away, so it took awhile to get it back. The machine shops labor rate is $110 an hour and it took an hour so it cost us $110. They did an excellent job. Hope this gives others...

try again...

....two more.

Here are a few of mine. Just my Mopars for now. :glasses7:

That is a stunning Nova. I have been building for 40 years and wish I could turn one out like that. :prayer::prayer::prayer:

I have the whole Pink Panther movie set on DVD, plus a bonus disc of all the cartoons. LOVE them. !!!

Sold !!

I know I would visit. I now own three '93 Grand cherokees. Two drivers and a parts one. I also own a 1942 Ford GPW, the "original" "Jeep". :D

Awesome builds guys. I'm a modeler as well. Will post up a few pics later when I have the time.