Search results for query: *

I can probably get somebody a real steal on a pair of compressors we have for sale at work.. You'll have no problem sandblasting anything-no matter the size or how long it will take. Wanna paint your Car? Bus? Locomotive? Jumbo Jet? all at the same time? No problem for you now! For...

Ah..I found the problem. The fuel filter was almost completely plugged with plastic shavings & junk from when the fuel cell was carelessly installed. This did not happen till now because the tank has less than 2 gallons in it. What is shown on the video is the pump pushing air (cavitating I...

Going to the shop now to check float level, won't have a good prs. guage installed till afterwork tomorrow. nm9- idle rpm's 1000 in N, no heat riser-M1 Single Plane, I will look down Primary bores, yes it does respond to Idle screws in Pri. Block, however Both Idle screws in Secondary Block have...

I will check that tomorrow Geo, thanks to you and Rick for your ideas. I am ordering a GOOD glycerin filled fuel prs. gauge to check the Aeromotive Electric pump.

No sir Rick, the rear vent is ok

Rick, the engine still pretty cool, in fact when I was done with all of this fooling around (oil fitting business, 3 separate video shoots of the vent & standin' there staring at it for some cyphering time) and shut it down the temp gauge was at ~~150 deg.

The vent has to be open to atmosphere-I closed it off w/my finger and the engine immediately died.

After replacing the leaking oil pressure fitting on the 360 block, I of course had to start it up and test my pipe fittin' skills. As the mill was idling, I catch a glimpse of this "fog" coming up and out the vent, then getting sucked down the carb. So.....Is this normal?? I'd appreciate some...

Buckets, 4 Gear-no console. I into vintage Street Muscle cars and that's where the Fire Extinguisher always is-Between the seats. No better place IMO. Jeff

Read the last line concerning the effects from the compressor oil that will get onto every square inch inside that PVC pipe. From U.S. Plastics: No, PVC and CPVC pipe should not be used for compressed air lines. Here is what the manufacture has to say about it. WARNING! The use of...

Yes

Since that StreetMachine has Bluedots, that alone makes it bargain at twice the price....Would'nt you agree?

Thank you for posting this! Turns out we have one of the recalled units. Ours runs 24/7 in the basement (machine shop), now will only plug it in when we are home.

No one has brought it up yet so I'll blurt it out-- get your fun side steppin' the clutch at 6 grand>bang the 1-2 & 2-3 with the ratchet shifter to the 727. ClutchFlite accept no substitute.

Thanks for everyones help. I have ordered the Throttle Lever Extension and a pair of return springs. However I am still trying to find the Throttle Lever Stud that would fit the clevis at the end of the cable. I've looked at Jegs, Holley, Summit & Dorman. I did find a pic of the stud, I only...

The pic won't load, I'll try to re-size..

Ok-here's the story..'68 Dart-360 Magnum w/single plane M1 & Holley 750 DP (1450). Bought the car last summer, drove it around-it seemed fast enough-somewhat. I just now got around to checking the pedal to the floor/all throttle plates wide open. Well, were about ~~70% on the Primarys and 0% for...

I'd like to spin up the oil pump & pre-lube the Magnum 360 before cranking the first time after winter storage. I don't have the store-bought shaft, but it "looks" like it's a piece of hex shafting that I cound easily make-up myself. If I'm correct, could someone measure the hex (standard or...

Ford > Traction-Lok and Equa-Lok Me> Detroit Locker...3.91

Hello All, I'd like to ask for suggestions on dealing with the aluminum corrosion on the carb and manifold. I'm not looking for Factory new appearence, just hints/tips/tricks that the masses here might have. This is the "as bought" condition and as $$ allows things like this will be...

Mobil Rarus 427... If it's good enough for the twin 350 HP Joy recip. compressors at the plant, I'm more than happy to feed to mine.

Single cut burr is recommended and always works best for me, load up the flutes with soapstone or chalk. Jeff

Replace lower ball joint on our '03 Subaru

From this new member in the NorthEastern corner of Ohio to ya' in your corner, Welcome to FABO. The '68 post partial *unplanned* re-wire.

Nice looking ride! --and move that battery to the trunk..................Tackweld

I trust the collective experts here can help me on this question... I have a 360 Magnum and pulled a valve cover to find the casting number. I could not find 7 numbers or "P" followed by 7 numbers anywhere. I did see 9970 on #1 intake runner then 5302 on #3 int. runner, I don't think these are...

Hi Everyone, Just starting to get back into the Street car crowd after 20+ years of raising kids/college,etc.. you know. I wanted '68/'69 Dart and hunted down a '68 fairly close to home. The seller trailered it to my place this morning and I spent the day at the Title/Tag office, then up on...