Search results for query: *

Should have a setup from 74

Even Wagons

I have these. Also have the column From 65 Coronet.

Thanks to all who helped me.

Hood to central Indiana? Ideas, cost?

Like the title says. I am looking for a hood for a 64 Dart. WOULD TAKE 63 or 64 since I think they interchange. Correct me if I am wrong. I am in Indiana. Thanks FABO

Pull the rear cover.

Look forward to your pics and maybe a little explanation of the "fudge".

Stroking increases piston speed. Piston has further to travel in one crank revolution. Hence increase in torque.

SOLD Thanks FABO

1967 Carter 4295 AFB and its accompanying factory intake, casting number 2536563 Located in north central Indiana. Carb will need rebuilt. It has waited a long time for the right project to come along. Believe those dreams are "poof ". Asking $165 plus shipping. Thanks FABO

Taking all advice on best solutions to repair lower quarters on 63 Dart Wagon. Are there any patch panels available for wagon? Modify sedan patches? Boneyard hunt? Thanks

My gut feeling has been too few springs in front clutch. I don't know if I want to dig that deep if....if a lever change might do it. Seems like here may be a few ways to correct or improve the condition. Thanks folks.

Tranny builder is very good. As I said, it has been many years since this project got going. I have been around the builder for many years. He is very respected. Most likely the input I gave him on what I thought I would use the car for has as much to do with the way it is set up...

I did not do the install. Local transmission shop handled it. I am going to see if he kept notes on it but, it was many years ago. If C-bodies use the low ratios I will assume he changed the lever. Car shifts great at WOT, but walkin' through town it clunks badly. I reckon I will have to...

Trying, like many I have read here, to remove a 2-3 shift overlap in a 727 that had a kit put in it years ago. The tranny was originally from a C-body after the introduction of the partial downshift. Used this tranny to possibly add a GVod someday in place of the original 65 cable shift...

A good chunk of change but, less than the last one I saw. Thanks

I happen to work in a small company that specializes in a different car brand. I have to agree with much of what RedFish has said. I also know the headaches of trying to keep a certain amount of inventory in stock. Keeping ten of everything you sell on the shelf is not feasible in a lot of...

That will definitely be the short term fix. Thanks

Sweet, figured if V8 might be in the future link would be the cure. Now, to find one. Anybody ever made their own? Seems like welding a drop would not be out of the question. Measure, measure again, cut, measure again, weld in pipe, measure again. Am I missing something here? Thanks

Looking at a 64 Dart 270. Once upon a time the /6 was changed to a later 74 and up motor. Noticed the pan resting on steering link which is well documented on this website. Would the V8 center link with its extra inch drop clear the pan and then be ready for a 273 later? Thanks folks

PM sent

I have a 4294, '67 not '66.

Looked at a 65 column I have left over from a Coronet. Believe it is the same as A body. The detent is on the column. In 66 and later non-cable shift tranny the detent would be in the tranny, correct?

By poking around this sight a little I was starting to suspect some bad things about steering columns. I am going to guess a 66 column is made of "unobtanium." Good to know about the pan. Would pan and pickup through 66 work?

Hello Folks, Trying to work through foreseeable problems. 65 Dart, original column shift. Donor motor and trans is 72 /6 with 904. How do I make it shift? Will 67 column work? Will donor 72 column work? Thanks

LOL Have straps. 92 Daks have no stake pockets or tie hooks, but I do have a tonneau cover for it. Thanks JD!

Hello Folks, Could someone break out the tape measure. Looking to pick up a 65 Valiant hood. Hoping it fits in the back of my 92 Dakota. Could someone please measure the width and the longest front to beck dimension. Would like to lay it down and reduce the potential of it becoming a...

SOLD! Thanks FABO!

North Central Indiana