Search results for query: *

I won't pull the distributor unless you not sure it in right. Check the wire you getting 12v from. Make sure it's has 12 all the time the key is on. Or find the two wire that feed the ignition and put the on the coil.

If it ran on a stand it should run in car. If you didn't remove any parts to get it in. I would check your wiring. Does it only want to run with the key in the start position?

yep. boy it didnt look deep like a cig lighter. thanks for the info..

This is in line with the radio. On the trim a little left of where yous is broken.

I own a 67 Barracuda and at a show this past friday I saw a 69 conv there. I have been going to this show for the most part every friday from mid summer last year. I was talking to the own and he asked me if i knew what was on his dash. It looked like a cig lighter but its to the right of the...

http://youtu.be/D3DzX50_JFk

It all depends what part of the state you move to. New England Dragway is close. Oxford is 1/8 mile and New England is 1/4 mile.

I put a post on your Maine question. If you need any more help just ask.

If you register as antique you don't need a inspection sticker. But it can't be your daily driver. If it looks all there with factory stuff the boys in blue shouldn't bother you. What part of Maine are you looking at?

Here is what I got. There are some very nice sounding mopars http://youtu.be/D3DzX50_JFk

Most all food. No fish or greens.

Also check out this valve OVERFLOW VALVE Fuel volume from the fuel transfer (lift) pump will always provide more fuel than the fuel injection pump requires. The overflow valve (a check valve) is used to route excess fuel through the fuel return line and back to the fuel tank. Approximately...

How far away is the dealer from you? There is a tool that plugs into the VP44 pump that will run the engine. THe tool number is 3163834. It will give you a hi/lo ldle and shut off. When I did the diesel work at my shop I loosend all but number 6. The VP44 pump will some times not like to bleed...

I have a 67 Barracuda notch back. I'm looking for pictures of the trim that hold or finishes off the headliner by the doors / roof line. Or if any body knows where I can get some. I have the A-pillar trim. Thanks for any help.

This is Ruger.

I don't know how big your shop is, we have 17 flat rate and two hourly. All but the hourly get pdi's. From the top paid tech to the low paid techs get pdi's. I have done a little work for the small guy's shop. I like dealer ships. Hang in there. Like some people tell me when I get grumpy at work...

Like I said in the Welcome Wagon I work for a dealership as a tech. For the last three years I have been doing some mite say restoration on trucks. Some of you in the salt belt may know what I'm talking about. RUST. Let's say it has been fun. But like evey flat rate tech knows the gravy train's...

Hay man I work at a dealership and somedays and weeks are better then others. The ? is are you flat rate or hourly? Dont know how your place works, but for me there are always alot of new cars to check in. They can make a bad day ok or a great day even better. If you are flat rate use the magic...

Ma Snart MP stand for Mopar Performance. It was nice working for a dealer and get part at cost.

Hay Ma Snart. I have I have a MP 360 short block with 340 heads. Best time on motor 12.8 and I have bottle fed it a few times with 100 hp shot it ran 12.2.

I would like to say thanks to all for saying hi. Badsport I was going to Rockland on Saturday to go to the Lobster Fest. But I think Mopar day at the drag great. Have not been in awhile.

To 383Duster I have no cool air to send to Tx. To I have family Houston area. To Badsport I live in southern Maine.

MP 360 short block with 340 heads.

Still working on it. But I have a little of the Mopar Muscle.

Just wanted to say hi. A little back ground of me. I was a Mopar tech for 13 years until my dealership closed. Had to go to another manufacture. Lets just say I got there at a good time. The car has been on the back burner for awhile and now its time to get back on it. I hope to help people and...