Search results for query: *

Sold the Swinger went to Wichita, Kansas Thanks for looking at my ad.

Still have Dart and looking to sell Dropped price to $7500.00 or make me an offer. Thanks

Still looking to trade or sale. Possible trades 91 to 93 Dodge diesel 4x4 65 to 67 coronet 65 to 67 Belvedere/ Satelite Or ?

Like the older Ford trucks but it still isn't a Dodge. Would consider a 91 to 93 Dodge Cummins 4x4 trade

Thanks for the offer. But if I am going to do a trade I want to trade for what I want.

Car is a good driver now just can't cruise over 55 for an extended period of time. LOL RPMs are at 3800 at 55 to 60 MPH. Just been short trips with it right now. Cam is couple sizes bigger than stock. Nice lope to it runs fine on pump gas. 10.25 to 1 on compression. 40 over on bore. Drums...

Also this Dart has just over 84,000 miles on the body. Has not been out in the rain or snowing 18 years. I was told I am third owner by the person I bought it from. Have not verified this. But condition of car I would say it actual. Origianlly a 318 car from factory. Has on small spot on...

8 3/4 rear end 489 case. big bolt pattern on the rear small bolt pattern on the front. drum brakes on all corner if i don't sell will have disc installed this winter on all four corners

Nice mean idle. 4.56 gear spooled. So it doesn't see very long trips right now. They will be changed out to 3.55s this winter if I don't sell.

Forgot to mention near Columbia, Missouri

Possibly looking to sell or trade my 1970 Dodge Dart Swinger. Rescently finished installing a 383. Has the Schumaker mounts, between the frame rail b body headers (followed the steps on bigblockdart.com), torker 2 intake and 750 Edelbrock carb, fuel cell electric fuel pump, new aluminum...

I used B body headers on my 70 Dart with a 383 auto. Used the shumacker conversion mounts. I followed the instructions on bigblockdart.com. I made the small dings in them where they show to make. It is a very tight fit. Also take loose the steering linkage and tie rods to make it easier to slide...

Thank you for all the PM's and replies I have located one. One step closer to having my Dart back on the road.

I will have to check on which one is on the drive shaft so I get the right one.

Needing a 727 slip yoke.

Drive really fast with the windows down LOL sorry couldn't resist.

Glad you found a radiator. Sorry I didn't send a pm I respond on the listing. Have a great weekend.

No pm received yet

It should fit. it just depends on what side your inlet and outlet are on. This radiator bottom bung is on the right (passenger side) and the top bung is on the left (drivers side). I put a 383 in my 70 Dart so I can't use the radiator the bungs are on the opposite sides. So I bought a...

More pictures

Pictures of seats

Have this picture which shows the radiator in the car. It is out of car and ready for someone.

Have two racing bucket seats with pads in excellent shape. $100.00 + shipping for the pair or will seperate at $50.00 each + shipping. Located in Mid Missouri Will try to post pictures later

Have a Griffin Radiator still need to sell part number 1-25222-X Was used on small block in my Dart. Also a trans cooler with it. Located in Mid Missouri. Asking $175.00 + shipping or make offer. I can text you picture computer at home crashed. send me a message

I would say they probably wouldn't work with power steering not much room left. I don't know if the shumacher tri ys will work with power steering . They would be a better one to use since they exit differently than these. I went with these because of the cost. Check on the bigblockdart web...

Some pictures of my 70 Swinger 383 project. More pictures to come as it progresses. 383 40 over custom ground Cam to 509 specs 10.25 to 1 compression. Headers 383 torker 2 intake Edlebrock 750 carb. Used the shumacker engine mounts. They worked great. Good instructions after setting it in...

trade pending

thursday would give me time to get them unbolted and out of the car lol

yes in missouri

interested in just selling the tracks?