Search results for query: *

if i let my truck set more than couple weeks in summer, couple days in winter i have to fill my bowl with gas before she'll fire off!! ant no problem when its warm weather, lot worse when cold weather! try and spin engine in hopes fuel pump will fill carb but itll run battery down before that...

when gasket matching magnum heads to a LA strip dominator intake what gasket do i use to match by??? felpro 1213S3's???

how can you check the fuel pump lobe on cam to be sure its stroking the pump arm fully?? got a high speed fuel delivery issue i trying to figure out!

any body know what the specs is for this engine? what heads is should have? cast or forged crank? rest the bottom end? would it be good core for a performance build? if it was a d150 i know its good,..but outta a D350 idk if the same!

when doing the 8.8 swap the extra short side axle dose it matter if its a drum brake axle if you got a disc brake rear end??

VEGE Remanufactured Engines 2D44 VEGE Remanufactured Cylinder Heads | Summit Racing 650 a set rebuilt ready to go...

just came across it scrolling.... Forabodiesonly

what all machines would be needed to do machine shop work? bore and deck blocks and heads? whats a good serdi machine cost?? crank grinder??

ant mine...

can a 85 318 be line bored .310 over to accept a 2.81 360 main journal?

We’re saddened to learn of the passing of Lee Roy Rumley, one of the most iconic owners in dirt late model racing history. From Davenport & McCreadie to Larson & Marlar, and many more, Lee Roy touched countless careers, all while remaining one of the nicest, most genuine men in the pits. We’ve...

on facespace marketplace, 25,000 bucks! no affiliation!

=AZU3g7W9I0cl_XRFeuEFzMVwZvhekHsK4vajspjSwr4fAb--eftB636RUTuIUg_b2xjW4tXQUHVxzn0ZF9tbwIqwHiMaWUDtjtwtJov8TALh1lQhAnltkd8zLVTLyHDEUyIGinpAWw1V5Vg2lx958dubrZLwN9vCiLIjGVlM6THur8uGjqcqX3IoW2WFnOOEKX1J0AKIIcfobJObs0W2mth6J3U7tB49YpvVpqFhmIFrEL-Jliv67yZWbOs12ZX0nMw&__tn__=-UC%2CP-y-R']Joey Arrington...

my fuel gauge and temp gauge only reading about 1/8 of what thay should! issue comes and gose, gauge respond fine 95% of the time! i dont like it and feel issue needs resolved before it becomes a bigger issue! ol truck ant been messed with much, only couple places wiring been opened from factory...

when using a 360 crank in a stroker 318 build, what best cheapest way to balance it all out? 318 car, converter and all what im working with. would it be best to use a LA crank or a magnum?

i know it ant a A body but best mopar tech is here and i trust yall! where can i find a nos or a good repop fuse block for a 1980 D150???

not mine, on FB market place...$600 bucks the add says!

1980 D150 2 speed wiper motor locked up and got to buy a new one, i see there's motors with delay and without, and mines without, cant find a switch for delay or non, whats different in the wiring between the 2???? can get delay by buying delay motor and finding a switch? or is there wiring...

Holley Sniper EFI 550-858 Holley Sniper EFI BBD for Jeep CJ more options slowly coming for our /6's!

would a well tuned small block with 10.37 static compression with good quench, and 7.89 dynamic compression and cranking pressure of 159.1 run on good pump gas? AJ/FormS how 7.89 dynamic gonna work with 2800ish stall in a 904 with 4:10 gears and 28 inch tire?

on a 85 318 how thick are the stock head gaskets?

not a A body but this is best place for any mopar wisdom ive found! noticed my 80 D150 was leaning on driver front other day. jacked it up and checked it out, broke lf coil spring. ant never seen one them brake before, seen them sag and droop!! wheres best place to get new springs and bump...

one my 2nd fuel pump in 2 weeks on this D150 and still having stuck needle jet issues,..figured i had rust and trash in tank and went to look about dropping it and its plastic, would it still be subject to rust?? is it worth pulling to be sure or move on to replacing rubber lines and assume...

got a 85 318 roller cam motor and thinking bout the magnum heads bang for the buck!! will the LA roller lifters pump oil up to valve train like the magnum lifters do or would i hafta buy magnum lifters to get it done???

chrystler kit built stock cars... The Chrysler Kit Car Log into Facebook | Facebook

any body ever try mod'in a stock intake for a holley 2280 carb? if so how did it work out? pro's con's???

know its not a A body, sorry, cant find any thing any where else! how in the world do you remove the distributor???? cant get the nut closest to fire wall! just can get a wrench on it no way to pull it!! was gonna replace the coil in it and leave it on but can get the screws out that hold the...