Search results for query: *

Thank you for the link!

Thank you, krazykuda! Exactly what I was looking for. Perhaps I will buy a service manual. Now that I am finishing

I do not have a service manual. I had the good fortune of disassembling a very complete car and am good with a camera and labeling. I do, however, have a number of measuring devices and the skill sets to use them! Thanks for the help!

Do you set by torque or measurment? Is there a specified "procedure"?

Think I can do a lot of hammering on the ones I have for 300 bucks!

I have not been on Laysons site for quite a while. I will check it out. Thanks for the tip to Classic Industries!

My 65 Barracuda resurrection is nearly complete. It is running beyond break in but has yet to move 1 foot under it's own power and that moment is upon me. I like it's stance as it is but it occurs to me that, beyond suspension assembly, no other adjustments have been made. In fact, none of the...



I am searching for an emergency brake handle. Just the plastic, I have rebuilt the mechanism. I need the headlight bezels. I have several pairs that are pretty well beat up. Rear window trim (what I call the trunk belt} All five pieces. I have two sets, 1 of average driver quality that I am...

Thanks, Joey and, thank you, Steve. I'll place an order

I would like to order a cap. Is it best to order from you here or use Ebay?

Thank you, everyone. It is a very sweet little motor! Glad to know of the coolant passages. I'll know to drain the radiator if manifolds need to be removed. Thanks Redfish I must admit, I was near panic mode! Thank you Rocky_JS and Grimreaper. Time for a test drive...

...understatement... As some here know, I am nearing the completion of my 65 barracuda. Essentially stock build on a 273 with a factory 4 speed. Had to move out of my shop last October, then got sick (understatement). Anyway, brought her home and fired her up for the first time before illness...

Looking for speedometer cable for my '65 Barracuda with 273 and 4 speed. Thanks for the help, as always! GS

Pretty much as I figured. Now I am curious as to weather or not this is the original engine for the car. I will replace the timing cover and water pump. Yeah, radiator too. How can I date the block? Should have looked into this before I started. Motor was already out of the car... The...

I thought about changing the water pump but, thought that would require changing the radiator. I had a difficult time finding this one and now believe it is not correct either. Lower hose is on driver side, upper is in the center. May end up changing the water pump and going with an aluminium...

I am ready to fire up the 273 in my 65 barracuda. I have spun it over and oil pressure came up quickly just off the starter. Hooked up my timing light to do a static set prior to start up. The timing gauge on the block is behind the lower water hose! No way to see the timing mark on the...

Thanks guys! Note: it is a 4 speed. Thanks, GRIMREAPER

This barracuda is a mildly built 273 with factory 4 speed and stock rear end. I am interested in what transmission fluid and rear grease to run and any recommended additives? Thanks to all comments! GJS

Sorry guys! Should have mentioned I need a 4 barrel Commando air cleaner. I would settle for a dent free painted one.

I believe it is

The tube is what I need most, Sedanman

Looking to the end on the 65 barracuda. Still need: Trunk trim (NOS or very nice) E brake handle Air cleaner Trunk lid prop When I think of anything else, I will add it here. Thanks everyone GJS

Figured it out. Best done with the hood off but, can be done with the hood on if you are creative with tools.

Nearly completed nut and bolt recreation... 273 4 sp. Bright blue metallic, white interior. No mods except Pertronix and Coy's 15" wheels with 235/60 - 15 GJS

The torsion springs have been off my 65 barracuda so long, I have forgotten how to install them. I would rather avoid damaging some paint so, thought I would ask here. if someone has pictures or a video they could post... Thanks to all GJSZ51

I am not familiar with "booster Dewey". Rebuilds boosters? Do you have contact info, clifftt? Any idea of his charge? GJS

Understood TMM, but need something in the hole until I find a "correct" replacement.

Thank you

Snapped mine off at the block and need a correct replacement . GJS