Search results for query: *

I am putting together a cast crank 400. My research indicates that the cast crank 400 and 440 engines used the same weights on the torque convertors. Does anyone know if the cast crank 340 and 360 LA engines used the same weights? I am looking for a stock 11 inch converter, and that would...

I purchased an inline electric fuel pump for the sole purpose of priming the carb when the car has been sitting for a week or two and all of the fuel has evaporated. I was thinking I just needed a momentary switch with two connectors to complete the circuit. As I usually do, I have been...

Anybody have a set they are not going to be using?

I have to do a small repair on my 2009 Honda Ridgeline. It is rusted between the gas filler door and the wheel lip, right where they all seem to go. I do have a mig welder but am a little concerned with welding that close to the gas filler. Any suggestions regarding a good body panel...

Does anybody know if a standard Holley accelerator pump nozzle (shooter) will fit a Street Demon carb? I looked up a picture and the register looks the same.

I bought a replacement sending unit but when I pulled out the original sending unit it cleaned up pretty well. I would like to reuse it. It needs a new float and sending unit filter. I was hoping I could use the ones from the new unit. Does anybody know how you can get the filter off the...

How do I shut off notifications being sent to my e-mail without shutting off alerts of replies on the site?

Does anyone know how many quarts it takes to refill a 727 after a filter change?

Here's the game. You get a blank check for up to one million dollars, which should be enough to cover all but the rarest muscle cars. You only get to buy one car, and it will be the only one you have. If you don't spend it all you don't get the left over money. It doesn't have to be a...

What is in the power steering return fitting. There seems to just be a spring. Is there supposed to be a check valve or something?

I am having my original power steering box rebuilt and upgraded for more feel. My federal pump was not leaking and was operating smoothly, so I really don't want to take it apart, but it was suggested that I flush it out to ensure there are no contaminants that could get into the fresh box...

I know that Edelbrock uses generic cams. I have a Wolverine cam which is the same as a Melling MTD2 and the same as the Edelbrock performer plus. I am looking for valve springs that will work with my stock retainers. The Edelbrock 5892 is on backorder everywhere. Does anybody have a Melling...

I did a compression test on my 361 and found one low cylinder, so I am getting ready to have the original 516 heads redone. Nothing fancy, perhaps change out the 1.60 exhaust valves for 1.74's. I was thinking just a 3 angle valve and a plunge cut, and then just blending out any ridges left...

I bought this cap at a swap meet a couple of years ago. It fits a stock electronic distributor. When it is on the rotor just hits the contacts inside the cap. You can see that they are larger than the stock ones. Question is could I just file some off the rotor contact for clearance? It is...

Looking for a Lunati Voodoo big block cam 10230700. It is 208/213 duration at .050 and 454/454 lift. I will purchase outright or I do have some brand new parts I could trade, for example a complete MSD billet distributor, coil and wires, and other parts.

Looking for a set of 15X7 or 15X8 steel magnum 500 wheels. I am in Canada so would probably have to ship to Niagara Falls NY for pick up.

After selling the cuda, and looking for a long time, I finally located a nice 1966 Charger and made a deal yesterday. The seller is headed out on vacation, so I will not be able to pick it for about a month, which may help weather wise. Since it's a B Body I may not be posting much here, but I...

I am thinking about my next build which will be an economy/performance 383 hopefully for a first generation Charger. The cam will likely be in the 210-220 range with low end torque more important than high end horsepower. I want a comfortable cruiser, that will get decent mileage cruising...

Sold the cuda about a month ago, and still looking for a 1966 or 1967 Charger, with decent driver quality paint and no rust. Engine size or condition is not as important. May also consider 1968-1970 Satellite or Coronet. Any leads would be great.

Can someone confirm whether the spindles for 10 inch drum brakes are the same as the ones for the Kelsey-Hayes disc brakes?

As some of you may know I sold the 'cuda. I am looking at a car listed on Minneapolis craigslist which is just west of Des Moines. Wondered if there is anyone on the board that is nearby who might be able to take a look at it for me before I make a 12 hour drive?

As some may know, I just sold my cuda. I am now looking for another project, a 1966 or 1967 Charger. It must be rust free with driver quality paint and interior. I do not want to deal with a lot of electrical gremlins. Engine size or condition is less important as that is the stuff I like to do.

Well after owing it for almost 25 years, and three engines and numerous trips down the racetrack, I sold the cuda today. Switching gears to a different car, more of a cruiser less of a racer. I have my eye on a 67 Charger, but nothing set in stone yet. We'll see what comes up.

I have owned this car for almost 25 years and taken it from a stock 318 first to a 400 that ran 12’s and then to a 500 stroker that runs 11’s. I run the car in full street trim with 3.55 gears and full exhaust, and it is well sorted and easy to drive on the street. I have driven it to car...

Did anyone get a name or phone number from the guy who was selling the aluminum magnum 500s at moparfest?

I have been thinking about building a reliable street engine for a heavy car, running A/C, power steering and brakes, throttle body fuel injection, and some form of O/D transmission. I used to run a 400 with a 222/234 cam, pocket ported heads (250 cfm), dual plane intake, 1 3/4 headers. It...

I just got a call from Eastwoods saying I won their draw at Carlisle. Shipping me a new tool in the mail. I can't remember which tool the draw was for. I think they said it was a surface conditioning tool, which would be neat.

Picked this up at Carlisle. Any guesses what it is?

Looking for a small ball joint socket. Shipping is a killer to Canada, but I will be in Carlisle next weekend and could pick up there if someone has one.

I just wanted to send a big thank you to Rick@Laysons. Years ago I bought a set of backup light bezels for the cuda, and they sat on the shelf. I finally got around to installing them and found there were two rights in the box instead of a right and a left. I messaged Rick and he agreed, even...